What to look at in live data
The pad wear sensor has no value among the standard OBD2 data: it is a simple circuit that opens or shorts to ground when the pad wears down to the wire. That is why the engine live data helps little here; what counts is a visual check of pad thickness, through the wheel or with it removed, and of the sensor lead.
If the pads still have material and the code stays, the sensor is broken, unplugged or its lead has been cut by the disc; after a pad change, if a new sensor isn't fitted (many are single use), the circuit stays open. On some cars the estimated pad thickness appears in the dashboard menu or the manufacturer's diagnostics: compare it with the real one, because after a change without resetting the calculation the estimate stays wrong.
How serious is it and can you drive?
Severity is medium. If the pedal feels normal and the car brakes well, drive gently to the garage, and soon. If you hear metal when braking, the pedal is soft or hard, or the car brakes badly, don't drive: call roadside assistance.
Read C004A on your car
With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.
Get DrivePulseWhat it means
The wear sensor is a wire embedded in the pad material at a set depth. As long as the pad has thickness, the wire stays whole. When the pad wears down that far, the disc cuts the wire, the circuit opens and the warning light comes on.
So C004A can mean two things: the pads are worn down to the mark, or the sensor or its wire broke on its own, from a knock, work on the wheels or a corroded connector.
Symptoms
- Brake warning light or pad wear light on.
- A message on the dashboard asking you to check the pads.
- A whistle or metallic squeal when braking, if the pads really are finished.
- No symptoms when braking, if the problem is just the wire.
Most likely causes, in order
- Worn pads down to the sensor: it's the most frequent cause.
- The sensor wire cut or crushed, perhaps during work on the wheels.
- The connector near the wheel corroded by water and salt.
- An old sensor refitted with new pads: if it was already worn through, the light stays on.
What to check before the garage
- Look at the brake fluid level in the reservoir, without opening it: with worn pads the level drops a little.
- On an empty road and at low speed, listen for a whistle or a metal noise when braking.
- Think back to when the pads were last changed, and whether the sensor was changed with them.
- Don't work on brake pipes, calipers or fluid yourself.
Pads or just the sensor?
That's the first thing to find out. If the pads are at their limit they need replacing soon: past the sensor there's little material left, then metal works against the disc, which gets damaged, and the car brakes less.
If the pads still have thickness, the fault is in the sensor or its wire. It's not as urgent as worn pads, but as long as the light stays on it won't warn you when they really are worn.
At the garage: what to ask
Measuring pad and disc thickness on both wheels of the same axle, and checking the sensor and its connector. In order of cost: sensor or connector, pads with a new sensor, pads and discs if metal has already touched.
What DrivePulse shows
DrivePulse shows C004A when the control unit that stored it responds on the OBD port, and opens the brake system card with the most important warning: if the pedal is soft or hard, or the car brakes badly, don't drive. It also tells you whether the code is pending or confirmed.
If brake pedal codes such as P0571 or P0504 show up too, it lists them alongside: they're part of the same system and are worth looking at together.
Frequently asked questions
Can I drive with C004A?
If the pedal feels normal and the car brakes well, yes, gently and soon to the garage. If you hear metal or the car brakes badly, no: call roadside assistance.
Do the pads need replacing?
Often yes: the sensor trips when they're at their limit. If they still have thickness, the fault is in the sensor or its wire.
Why does the light stay on after new pads?
Usually because the old, already worn sensor was refitted, or the connector isn't clipped in properly. On some cars the wear indicator also has to be reset at the garage.
Related codes
Related guides
- Buying a used car? What to check: a code cleared just before the sale shows up in the distance driven since the last clear.
What you need to read it
All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.
DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.