EN ▾
EnglishItalianoDeutschFrançaisEspañolPortuguêsČeštinaPolskiMagyarRomână
Download
  1. DrivePulse
  2. Fault codes
  3. Accelerator, idle and brake
  4. P0571

P0571: brake switch A circuit malfunction

The switch on the brake pedal tells the control units when you brake. With P0571 one of its circuits, circuit A, has an electrical fault. The first check is simple: do the brake lights come on?

Get DrivePulse

What to look at in live data

Contact A of the brake switch is usually the one that turns on the brake lights and tells the engine ECU; its state isn't among the standard OBD2 data, and only some cars show it through the manufacturer's diagnostics. The clearest signs are outside the data: brake lights that don't come on or stay on, cruise control that cuts out by itself or won't start, an automatic gear lever that won't leave P without forcing it.

If the car reports the brake state, watch it with the pedal at rest and then pressed gently: it should change as soon as the pedal moves, and switch back as soon as you let go. If it never changes, check the brake light fuse and the switch connector; if it only changes with the pedal pressed fully, the switch is out of adjustment. A signal that flickers on and off with the pedal at rest, over bumps, means a tired contact.

How serious is it, can you drive?

Severity is medium. The brakes still work, but if the brake lights don't come on, the driver behind can't see you slowing down. In that case drive very gently, leaving more distance, only as far as the garage, and don't use cruise control.

Read P0571 on your car

With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.

Get DrivePulse

What it means

Above the brake pedal there is a switch, or a sensor, that tells the control units when you press the brake. On many cars there are two signals, called A and B: one turns on the brake lights, the other goes to the engine ECU. The ECU uses it to cancel cruise control, to let the automatic gear selector out of P, and to run start-stop and the safety systems.

With P0571 the ECU sees an electrical fault in circuit A: the signal is missing, never changes or is outside the expected values. That is different from P0504, where both circuits work but don't agree with each other.

Symptoms

  • The brake lights don't come on, or stay on all the time.
  • Cruise control won't engage, or doesn't cancel when you brake.
  • On automatics the selector won't come out of P, or the engine won't start.
  • Engine light on, sometimes with the safety system or start-stop warnings too.

Most likely causes, in order

  • The switch knocked out of place or out of its holder above the pedal, often after a kick.
  • The switch connector loose or unplugged.
  • The brake light fuse blown.
  • Damaged wiring under the dashboard.
  • An internal fault in the switch.

What to check before the garage

  • The brake lights: ask someone to watch while you press the brake, or look at the reflection in a shop window or a garage door. They must come on at once and go off as soon as you release the pedal.
  • That the floor mat isn't blocking the pedal: it must come all the way back up.
  • With a torch under the dashboard, that the switch is in place and the connector plugged in.
  • The brake light fuse, shown in the owner's manual.

At the garage: what to ask for

A live reading of the switch state while the pedal is pressed and released, a check of the connector, wiring and fuse, then adjusting or replacing the switch. It is usually a short job.

What DrivePulse shows

DrivePulse reads P0571 and its card tells you to start with the brake lights, using the reflection in a shop window if you're on your own; it also tells you whether the code is pending or confirmed.

If P0504 or P0500 show up too, DrivePulse lists them together: on many cars the brake signal is compared with others, and a single fault drags others along with it.

Frequently asked questions

Can I drive with P0571?

Only as far as the garage, gently, if the brake lights don't work. If they do, the risk is lower, but leave cruise control off.

What's the difference from P0504?

P0504 says the two switch signals, A and B, don't agree. P0571 says circuit A has an electrical fault.

Why won't the automatic selector come out of P?

For safety it only unlocks with the brake pressed, and the ECU learns that from this switch. If the signal doesn't arrive, the selector stays locked.

Related codes

Related guides

What you need to read it

All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.

DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.

← All codes