What to look at in live data
If the car reports clutch switch status, test it with the car stationary, the engine off and the ignition on: pressing the pedal slowly all the way down, the status should change once, always at the same point of the travel, and change back when you release it. If the car has two switches, both should change, each at its own point.
If the status never changes, the switch is disconnected, faulty or out of adjustment. If it changes erratically, or only when you press hard at the end of the travel, it is badly adjusted or worn. Repeat the test several times: a contact that fails once in ten is enough to set the code.
How serious is it, can you drive?
Severity is low. The engine and gearbox aren't harmed, and you can drive gently. The nuisance is losing cruise control and start-stop, and on some cars the risk of being stranded because the engine won't start. It's worth fixing soon, not least because it's a simple repair.
Read P0704 on your car
With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.
Get DrivePulseWhat it means
On manual cars, one or two switches on the pedal box signal when the clutch is pressed. The ECU uses this to cancel cruise control, to run the start-stop system, to smooth gear changes and, on many cars, to allow starting only with the clutch pressed.
With P0704 the signal is missing, never changes or doesn't fit with the rest. For example, the ECU sees the gears change, meaning the ratio between engine revs and road speed, without the switch ever reporting the clutch as pressed.
Symptoms
- Cruise control won't engage, or drops out on its own.
- Start-stop stops working.
- On some cars the engine won't start, or starts even without pressing the clutch.
- Some jerkiness when changing gear, because the ECU no longer eases off the engine.
Most likely causes, in order
- The switch on the pedal has failed or is out of adjustment: it works on every gear change and wears.
- The switch connector is loose, perhaps after work under the dashboard or a mat that knocked it.
- Broken wires near the pedal box, where they flex with every press.
- A floor mat stopping the pedal from returning fully, more rarely.
What to check before the garage
- That the floor mat hasn't slipped under the pedal: the clutch must come all the way up and go all the way down.
- With a torch, look under the dashboard to see whether the connector on the clutch switch is in place.
- If the car won't start, press the clutch firmly all the way down: a misadjusted switch sometimes only closes at the very end of travel.
At the garage: what to ask for
A reading of the switch state with the diagnostic tool while the pedal is pressed and released, then adjustment or replacement of the switch and a connector check. It's a quick job.
What DrivePulse shows
DrivePulse reads P0704 and its card explains why cruise control and start-stop stop working; it also tells you whether the code is pending or confirmed.
If after the adjustment the code stays pending and doesn't confirm again over the next trips, the repair has worked.
Frequently asked questions
Can I drive with P0704?
Yes, gently: the engine and gearbox aren't harmed. You lose cruise control and start-stop.
Why doesn't the cruise control work?
Because the ECU must know when you press the clutch in order to cancel it. If it doesn't trust the switch, it keeps cruise control off for safety.
The car won't start, is P0704 to blame?
It can be: on many cars starting is only allowed with the clutch pressed. Press the pedal all the way down and have the switch checked.
Related codes
Related guides
- Buying a used car? What to check: a code cleared just before the sale shows up in the distance driven since the last clear.
What you need to read it
All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.
DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.