What to look at in live data
The value to watch is the voltage the ECU reads. With the engine off and the battery rested for a few hours, a charged battery sits around 12.6 V; below 12.2 V it is about half charged. With the engine running the alternator should bring it to roughly 13.5 to 14.7 V, even with lights and fan on. Cars with smart charging (start-stop, brake energy recovery) deliberately hold about 12.3-13 V at a steady speed and go up to about 15 V when the driver lifts off: there, what counts is that the voltage rises on lift-off or with loads switched on, not a fixed number, and on the move the phone is held by the person in the passenger seat.
If it stays below 13 V with the engine running and does not rise on lift-off or with loads on either, suspect the alternator, its belt or the ground cables. If it is fine with the engine running but the battery goes flat while parked, something drains it with the car off, or the battery no longer holds a charge.
How serious is it and can you drive?
Severity is high, because the real risk is being stranded. If the voltage is low with the engine running, the alternator isn't charging and the car runs on the battery alone, for as long as it lasts. Only drive as far as the garage or home, without switching on everything that draws power, and don't switch off where you couldn't restart.
Read P0562 on your car
With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.
Get DrivePulseWhat it means
With the engine running, the alternator charges the battery and powers the whole car, and the voltage stays around 14 volts. With the engine off, the battery carries everything. The ECU constantly checks the voltage it receives: if it stays below the expected threshold for a while, it stores P0562.
Low voltage doesn't only affect starting: many control units misbehave below a certain voltage, and other odd codes can appear, communication or sensor faults, which vanish once the voltage is right again.
Symptoms
- Slow starting, the starter turns lazily.
- Lights dimming at idle or when you switch something on.
- Battery warning light on.
- Other codes or lights that come and go for no reason.
Most likely causes, in order
- The battery, flat or at the end of its life, especially past four years old and in winter.
- The alternator not charging enough.
- The auxiliary belt slipping or broken.
- Terminals or earth connections corroded or loose.
- A parasitic drain that empties the battery while the car is parked.
What to check before the garage
- Look at the battery terminals: white or green corrosion, a terminal that moves by hand. Clean and tighten them, with the engine off.
- Measure the voltage with the engine off for a few hours: around 12.6 volts the battery is charged, below 12.4 it's flat.
- Measure it with the engine running: it should be between 13.8 and 14.7 volts. If it stays below 13, the alternator isn't charging.
- Look at the auxiliary belt: cracks, a glazed surface, a squeal on starting.
At the garage: what to ask for
A battery load test, a check of the alternator's output at different revs and, if the battery drains while parked, a parasitic draw measurement. A new battery on an alternator that doesn't charge goes flat again within days: both get checked.
What DrivePulse shows
DrivePulse reads P0562 and opens its card, with the warning to deal with it now. In Health you find the battery voltage: at rest it tells you whether it's charged, while driving whether the alternator is charging it. The cranking battery test captures the lowest voltage while the starter turns, the real test of a tired battery.
Through the OBD port the voltage can read 0.2 to 0.4 volts lower than at the battery terminals: what matters is the trend, measured the same way each time.
Frequently asked questions
Is it the battery or the alternator?
You can tell with the engine running: if the voltage is between 13.8 and 14.7 volts the alternator is charging, and the battery is the likely culprit. If it stays below 13, it's the alternator or the belt.
Can I drive with P0562?
Only as much as you need to. If the alternator isn't charging, the car runs on the battery until it's empty, and then stops.
Why do other odd codes appear at the same time?
Because many control units misbehave below a certain voltage and store communication or sensor errors. They often disappear once the voltage is right again.
Related codes
Related guides
- Buying a used car? What to check: a code cleared just before the sale shows up in the distance driven since the last clear.
What you need to read it
All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.
DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.