What to look at in live data
Here the problem is in the motor that opens and closes the throttle, or in the current that drives it. In the standard data, compare commanded throttle actuator with absolute throttle position, with the engine warm: at idle the two should almost match, and a firm press of the pedal while parked should bring the actual position where the command asks, without stopping halfway.
If the gap appears only sometimes, watch the control module voltage at the same moment: the throttle motor draws a lot of current on fast moves and suffers with a weak battery or corroded grounds. If the gap is always there, the throttle body is dirty or the motor is worn. Either way the car can go into limp mode, with limited revs, until the engine is switched off and on again.
How serious is it, can you drive?
Severity is high: with reduced power, overtaking or joining a fast road becomes dangerous, and on some cars the engine can stall. Drive very gently, only as far as the garage, away from motorways and dual carriageways.
Read P2101 on your car
With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.
Get DrivePulseWhat it means
The ECU doesn't drive the throttle with a simple on and off: it sends the motor pulses of varying length and watches how much current it takes to reach the requested position. If moving it takes far more effort than normal, or the motor responds in jerks, it logs P2101.
The code is about the electrical side of the control: the motor, its wires and the connector. A gummed-up or stiff throttle, though, makes the motor work harder, which is why dirt often leads to P2101 too.
Symptoms
- Check engine light on and much less power: the car revs poorly and struggles to accelerate.
- High or uneven idle, sometimes an engine that stalls when you lift off the accelerator.
- On some cars the stability control light comes on too, or an engine fault message appears.
- Switching the engine off and on again can bring the power back, until the fault returns.
Most likely causes, in order
- The throttle body connector, corroded, loose or with a terminal that doesn't make contact.
- A gummed-up throttle, coated with oily deposits from the crankcase breather or exhaust gas recirculation, that moves with difficulty.
- Low system voltage: a weak battery or a corroded engine ground, leaving the motor without strength.
- The wires between throttle body and ECU, damaged or shorted.
- A worn motor or worn gears: then the throttle body is replaced.
What to check before the garage
- With the engine off, unplug and reconnect the throttle body connector and look for corrosion or bent terminals.
- Check the battery terminals and the engine ground: if they're loose or green, have them cleaned and tightened.
- Remove the air hose in front of the throttle and see whether the valve is black and gummed up.
- If the car is in limp mode, no acceleration tests: take it only as far as the garage.
P2101, P0638 and P2135: what each one watches
They're three different checks on the same part. P2135 compares the two position sensors inside the throttle with each other. P0638 compares the requested position with the one reached. P2101 monitors the circuit of the motor that moves it.
They often show up together, because a struggling motor also makes the throttle arrive late. The code that was logged first, and the ones that come back after the repair, help you decide where to start.
At the garage: what to ask for
A check of the connector and wiring, a motor test from the scan tool and, if the throttle is dirty, cleaning followed straight away by the position relearn. In order of cost: connector and ground, cleaning with relearn, wiring, new throttle body.
What DrivePulse shows
DrivePulse reads P2101 and opens the throttle body card: what the part does, the advice to drive very gently to the garage if the car goes into limp mode, and whether the code is pending or confirmed.
In Health, the cranking test and the resting voltage tell you whether a weak battery could explain the fault. In the live data, on cars that report it, the throttle position shows, with the car standing still, whether it follows the pedal.
Frequently asked questions
Can I drive with P2101?
Only very gently and as far as the garage: power is reduced and when overtaking you won't get the push you expect.
What's the difference from P0638?
P0638 compares the throttle position with the requested one; P2101 monitors the circuit of the motor that moves it. They often appear together.
Is cleaning the throttle enough?
Sometimes, if it was gummed up, but after cleaning the position relearn is needed. If the motor is worn, the throttle body is replaced.
Related codes
Related guides
- Buying a used car? What to check: a code cleared just before the sale shows up in the distance driven since the last clear.
What you need to read it
All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.
DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.