EN ▾
EnglishItalianoDeutschFrançaisEspañolPortuguêsČeštinaPolskiMagyarRomână
Download
  1. DrivePulse
  2. Fault codes
  3. Accelerator, idle and brake
  4. P2138

P2138: accelerator pedal position sensor D/E voltage correlation

Pedal positions D and E are in standard OBD2 data: with the ignition on and the engine off, press the pedal slowly to the floor; both must rise together and smoothly, keeping the same ratio. If one jumps or stops while the other goes on, the track is worn there. Drive only to the garage, carefully.

Get DrivePulse

What to look at in live data

The two pedal positions, D and E, are among the standard OBD2 values. With the engine off and the ignition on, they have different but steady values with the pedal released; pressing the pedal slowly all the way down, they should rise together, smoothly, always keeping the same ratio to each other (often one is about half the other).

If one of them jumps, stalls or goes backwards at one point of the travel while the other carries on, the sensor track is worn right there. If the jump shows up when you gently move the pedal connector or cable, still with the engine off, the problem is in the wiring.

How serious is it and can you drive?

Severity is high, because it concerns the accelerator. In limp mode the car picks up speed slowly, and joining a fast road or overtaking becomes dangerous. Drive carefully, only as far as the garage.

Read P2138 on your car

With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.

Get DrivePulse

What it means

On modern cars the accelerator pedal doesn't pull a cable: it's a sensor that tells the ECU how far you're pressing it. For safety there are two sensors, called D and E here, with different but related voltages. The ECU compares them constantly. With P2138 it says the two signals don't add up: one says one thing, the other another. Not knowing which is right, it restricts the engine.

Symptoms

  • The car responds little or not at all to the accelerator.
  • Limp mode, with the engine revving up slowly.
  • Check engine light on, sometimes the stability control light too.
  • Cruise control won't engage.

Most likely causes, in order

  • A worn pedal sensor: it's built into the pedal and its internal tracks wear over the years.
  • The pedal connector, loose or corroded.
  • Wiring damaged near the pedal, sometimes by a floor mat or work under the dashboard.
  • An unstable supply voltage, from a weak battery or corroded earths.

What to check before the garage

  • Make sure no floor mat touches or presses the pedal.
  • With the engine off, look at the connector on top of the pedal: fully seated and not corroded.
  • If water has got inside the car, through the windscreen or doors, tell the garage: moisture near the pedal is a common cause.

At the garage: what to ask for

A reading of the two pedal signals while the pedal is pressed slowly through its whole travel: they should rise together without jumps. If one signal jumps, the whole pedal assembly, which contains the sensor, is usually replaced.

What DrivePulse shows

DrivePulse reads P2138 and opens its card, with the warning to drive carefully to the garage and the advice to check the floor mats. In Health, battery voltage helps rule out an unstable supply.

If P2135 appears too, DrivePulse shows both: when problems affect both pedal and throttle, suspicion moves to the power supply or a shared earth.

Frequently asked questions

Can I drive with P2138?

Only as far as the garage, carefully. In limp mode the car accelerates poorly, and joining fast roads becomes risky.

Does the pedal need replacing?

Often yes: the sensor is inside the pedal and the whole assembly is replaced. The connector and wiring get checked first.

Why do the two sensors have different voltages?

So that a short or a disconnected wire shows up straight away. If the two signals were identical, a fault affecting both could fool the ECU.

What's the difference from P2135?

P2138 concerns the two accelerator pedal signals. P2135 concerns those of the throttle, or in some cases the pedal, with different letters. The principle is the same: two signals that don't agree.

Related codes

Related guides

What you need to read it

All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.

DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.

← All codes