What to look at in live data
P0606 is a fault the ECU finds in itself, during its internal checks, and no live data value measures the processor. What matters is the environment it works in: check the control module voltage with the engine off (above about 12.4 V with a charged battery), while cranking (not below 10 V) and with the engine running (roughly 13 to 15.5 V, lower for stretches on cars with smart charging).
If the voltage sags or jumps, or the code appeared after a jump start, a battery replacement or work on the wiring, the problem may be outside the ECU: corroded grounds, damp connectors, voltage spikes. See also whether the live data arrives in bursts or communication drops: with a faulty processor the ECU sometimes resets, and the engine stumbles for a moment. Only after power and grounds are ruled out does reprogramming or replacing the ECU make sense.
How serious is it and can you drive?
Severity is high, because the unit that controls the engine isn't sure of its own calculations and may stall the engine or cut power suddenly. Only drive as far as the garage, avoiding motorways and overtaking.
Read P0606 on your car
With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.
Get DrivePulseWhat it means
The engine ECU has more than one processor, or a processor with an internal monitor, that cross-check the most important calculations, such as those for the accelerator. If the two results don't match, or the internal memory fails a check, the ECU stores P0606. It often enters limp mode too, for safety.
The code tells you where the error was seen, not always why. An unstable voltage, a corroded earth or electrical interference can make a healthy ECU fail its internal checks.
Symptoms
- Limp mode, with the accelerator responding weakly.
- Sudden stalling or hard starting.
- Other communication or sensor codes alongside.
- Problems that come and go, often when cold or damp.
Most likely causes, in order
- Unstable power supply: a weak battery, corroded terminals, a loose engine or ECU earth.
- The ECU connector with moisture or corrosion.
- ECU software with a known bug that the manufacturer fixes with an update.
- The ECU really failing.
What to check before the garage
- The battery's condition: resting voltage, age, slow starts.
- The battery terminals and the visible earth straps between engine and body: clean and tight, with the engine off.
- If the car has been exposed to water (engine wash, flooding, a leaking windscreen), tell the garage: moisture in connectors is a common cause.
At the garage: what to ask for
Power and earth checks first, with the voltage measured right at the ECU pins. Then a check for manufacturer software updates for that code. The ECU comes last: it can often be repaired, which costs less than replacing it, and a replacement has to be programmed for the car anyway.
What DrivePulse shows
DrivePulse reads P0606 and opens its card, with the advice to check the battery and earths before suspecting the ECU. In Health you find the battery voltage at rest and while driving, and the cranking test: if the battery is weak, it's the first suspect.
DrivePulse also shows the other stored codes: communication or voltage errors strengthen the case for a power supply problem.
Frequently asked questions
Does P0606 mean the ECU is finished?
No. The cause is often the power supply, an earth or software that needs updating. And even when the ECU is faulty, it can often be repaired.
Can I drive with P0606?
Only as far as the garage. The ECU may limit power or stall the engine suddenly.
Can a new battery fix it?
Yes, if unstable voltage was the cause. If the code returns with battery and earths in order, the software gets checked, then the ECU.
Related codes
Related guides
- Buying a used car? What to check: a code cleared just before the sale shows up in the distance driven since the last clear.
What you need to read it
All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.
DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.