EN ▾
EnglishItalianoDeutschFrançaisEspañolPortuguêsČeštinaPolskiMagyarRomână
Download
  1. DrivePulse
  2. Fault codes
  3. Electronics and communication
  4. P0607

P0607: control module performance

No live value shows whether the ECU works inside, but you can rule out what upsets it: check the supply voltage it reports with the ignition on, while cranking and at idle with lights and fan on; dips below 10 to 11 V are enough. If the car drives normally you can go gently, but have the battery checked soon.

Get DrivePulse

What to look at in live data

As with other internal faults, no live value tells you whether the ECU is working properly inside: P0607 comes from its self-checks. What you can do is rule out what makes it go wrong. Watch the supply voltage the ECU itself reports, with the ignition on and the engine stopped, while cranking and then at idle with headlights and fan on: dips below 10 to 11 V or sudden jumps are enough to make an internal check fail.

Then see whether other codes are present at the same time, especially communication codes (the ones starting with U) or sensor supply codes: if they show up together, the cause is often an ECU connector with water or corrosion, or a loose engine ground. If P0607 is alone, with a steady voltage, and returns every time the garage clears it, the ECU needs checking by the brand's service, which can update or replace it.

How serious is it and can you drive?

Severity is medium. If the car drives normally you can drive gently, but don't ignore it: it's often the first sign of a battery about to let you down. If stalling or limp mode appears, only drive as far as the garage.

Read P0607 on your car

With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.

Get DrivePulse

What it means

With P0607 the ECU says one of its internal performance checks failed: an unexpected restart, a calculation time out of spec, an internal circuit not responding as expected. It's a close relative of P0606, but usually less serious.

Control units are very sensitive to the quality of their power supply. A voltage dip lasting an instant, while cranking or from an earth that makes poor contact, is enough to make them restart uncleanly and store this code.

Symptoms

  • Often just the light.
  • The odd hard start, or idle dipping for a moment.
  • Dashboard instruments switching off and on while cranking.
  • Other communication codes alongside, coming and going.

Most likely causes, in order

  • A weak battery that lets the voltage drop too far while cranking.
  • Corroded or loose earths between engine, body and ECU.
  • The ECU connector with corrosion or moisture.
  • Software that needs updating.
  • The ECU, if everything else is in order.

What to check before the garage

  • The battery: age, resting voltage, how the starter turns when cranking.
  • The terminals and visible earths: clean and tight, with the engine off.
  • If the code appeared after a jump start or after disconnecting the battery, note it: it often explains everything.

At the garage: what to ask for

A battery load test and a voltage drop test on the earths, then a check for software updates. The ECU is only looked at if the code returns with a perfect power supply.

What DrivePulse shows

DrivePulse reads P0607 and opens its card, which says straight away that the problem is often the battery or an earth. In Health you find the resting battery test and the cranking test: a deep dip while the starter turns is exactly the kind of disturbance that confuses control units.

DrivePulse also tells you whether the code is pending or confirmed: a P0607 that appears once after a hard start and then goes away tells a different story from one that stays.

Frequently asked questions

Can I drive with P0607?

If the car drives normally, yes, gently. But get the battery and earths checked soon: it's often the first sign of a tired battery.

What's the difference from P0606?

They're related. P0606 is about a processor error and usually weighs more; P0607 about abnormal operation, often caused by the power supply.

Can it appear after disconnecting the battery?

Yes. An interrupted or unstable supply during work on the car can store P0607. If it doesn't return after a few drives, it wasn't a fault.

Related codes

Related guides

What you need to read it

All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.

DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.

← All codes