What to look at in live data
Many engine sensors get the same 5 V reference voltage from the ECU: throttle, pedal, manifold pressure, fuel pressure, sometimes the camshaft. With P0642 that voltage is low, so every sensor that uses it goes wrong at once. In the standard data that is exactly the typical sign: several values wrong at the same time, for example pedal and throttle at zero, impossible manifold pressure, and the car in limp mode.
The culprit is often one shorted sensor dragging everyone's voltage down. With the ignition on and the engine off, watch the values while you unplug the 5 V sensors one at a time: when you unplug the shorted one, the others jump back to normal. If none of them changes anything, the short is in the wiring (a crushed or chafed wire) or in the ECU itself.
How serious is it and can you drive?
Severity is high. Drive gently and only to the garage: with several sensors unpowered the car can go into limp mode or stall, even at an awkward moment.
Read P0642 on your car
With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.
Get DrivePulseWhat it means
Engine sensors, such as the accelerator, pressure or position sensors, don't produce power on their own: the ECU feeds them a reference voltage and reads what comes back. To save wires, several sensors share the same line, called A, B and so on.
With P0642 line A is too low. Which sensors sit on it depends on the engine: the manufacturer's wiring diagram says.
Symptoms
- Several warning lights and codes at once, from different sensors.
- Reduced power or limp mode.
- Accelerator pedal that barely responds, if its sensor is on the same line.
- In some cases the engine won't start or stalls.
Most likely causes, in order
- A shorted sensor, damaged by a knock or by heat, pulling down the supply for all the others on the same line.
- A supply wire squashed or bare, touching ground.
- A sensor connector with water inside, after an engine wash or driving through deep water.
- More rarely, the ECU, with an internal fault.
What to check before the garage
- Think about any recent work, a knock or an engine wash: tell the garage, it's the most useful clue.
- Look at the wiring you can see in the engine bay: no squashed, burnt or bare wires.
- Note all the other codes that appear with it: the sensors they name are the first suspects.
Why so many codes at once
When line A drops, every sensor on it sends wrong values at the same moment, and the ECU logs a code for each. It looks like many faults, but it's usually just one.
That's why replacing the sensors in the list isn't worth it: the part to find is the shorted one, and it's often not even among the first named.
At the garage: what to ask
Measuring the voltage on line A, then unplugging the sensors one at a time until the voltage returns to normal: that finds the shorted one. In order of cost: drying or cleaning a connector, repairing a wire, the shorted sensor, and only last the ECU.
What DrivePulse shows
DrivePulse reads P0642 and opens the card for the circuit that powers the sensors, with the advice to drive only to the garage; it also tells you whether the code is pending or confirmed. It shows all the stored codes in one list: if they name different sensors, that's the sign the shared supply is missing.
In Health you'll find the battery voltage at rest and while driving: it helps rule out the battery or the alternator as the cause of the drop.
Frequently asked questions
Can I drive with P0642?
Only gently to the garage. With several sensors unpowered the car can go into limp mode or stall.
Why do I have so many codes from different sensors?
Because those sensors draw power from the same line. When the line drops, they all go wrong together: usually there's only one fault.
Is the ECU broken?
Rarely. Much more often it's a shorted sensor or wire, which the garage finds by unplugging the sensors one at a time.
Related codes
Related guides
- Buying a used car? What to check: a code cleared just before the sale shows up in the distance driven since the last clear.
What you need to read it
All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.
DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.