EN ▾
EnglishItalianoDeutschFrançaisEspañolPortuguêsČeštinaPolskiMagyarRomână
Download
  1. DrivePulse
  2. Fault codes
  3. Accelerator, idle and brake
  4. P2135

P2135: throttle position sensor A/B voltage correlation

The two throttle position sensors are in standard data: with the ignition on and the engine off, press the pedal slowly all the way and back; they read different values but must move together, with no jumps. Gently moving the throttle connector shows a loose contact. Drive only to the garage, carefully: limp mode leaves little power.

Get DrivePulse

What to look at in live data

The two throttle sensors appear in the standard data as absolute throttle position and throttle position B. They don't read the same value, but they must move together: with the ignition on and the engine off, press the pedal slowly all the way down and back, watching that neither one jumps, stops or goes backwards while the other rises.

Repeat the test while gently wiggling the throttle body connector: if the values jump about, the bad contact is there. If the two signals agree with the engine off but the code returns on the road, watch commanded and actual throttle position during an easy drive, with the phone in the hands of the person in the passenger seat: a gap that appears with vibration points to a worn sensor track, and usually the whole throttle body is replaced.

How serious is it and can you drive?

Severity is high. Limp mode takes away power and can make joining fast roads dangerous; sometimes the engine stalls. Drive carefully, only as far as the garage.

Read P2135 on your car

With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.

Get DrivePulse

What it means

On petrol engines, and many diesels, the throttle that meters air is moved by a small motor driven by the ECU. Two sensors inside the throttle body, A and B, read its position independently, because an error here could make the car accelerate on its own. The ECU compares the two values: with P2135 it says they disagree. For safety it restricts the engine or holds it at idle.

Symptoms

  • Limp mode: little power, limited revs.
  • Rough idle, sometimes stalling.
  • The engine responds late to the accelerator.
  • Check engine light on.

Most likely causes, in order

  • A dirty throttle body or worn internal sensors.
  • The throttle body connector, corroded or loose.
  • Wiring damaged between throttle body and ECU.
  • An unstable voltage, from a weak battery or corroded earths.

What to check before the garage

  • With the engine off, check the throttle body connector is fully seated and not corroded.
  • Look at the wiring near the throttle body: no stretched or damaged wires.
  • Check the battery: low voltage when cranking can bring up codes like this.

Why a relearn is needed after cleaning

The ECU stores the exact closed position of the throttle and the small idle corrections. After cleaning or replacement those values no longer apply: without the relearn procedure the idle can stay high or uneven and other codes can appear, such as P0507. On many cars the garage tool does it; on others a key and pedal sequence set by the manufacturer is enough.

At the garage: what to ask for

A reading of both throttle signals while the tool moves the throttle, then cleaning the throttle body and running the position relearn procedure. If a sensor is worn, the throttle body is replaced.

What DrivePulse shows

DrivePulse reads P2135 and opens its card, with the limp mode warning and the advice to check the connector. In the live data, on cars that report it, you see throttle position: if it jumps or doesn't follow the pedal smoothly, the picture fits.

In Health, battery voltage helps rule out an unstable supply, a common cause when P2135 and P2138 appear together.

Frequently asked questions

Can I drive with P2135?

Only as far as the garage, carefully. In limp mode there's little power and the engine may stall.

Can cleaning the throttle body be enough?

Sometimes, if dirt is disturbing its movement. After cleaning, a relearn is needed. If an internal sensor is worn, the throttle body is replaced.

What's the difference from P2138?

P2135 concerns the throttle sensors, P2138 the accelerator pedal ones. If they appear together, look at the power supply first.

Related codes

Related guides

What you need to read it

All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.

DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.

← All codes