What to look at in live data
P253F doesn't come from a fault but from a calculation: many ECUs estimate oil wear by counting kilometres, cold starts, hours at idle and, on diesels, particulate filter regenerations, which dilute the oil with fuel. The standard data shows the ingredients of that calculation: coolant temperature and, if the car reports it, oil temperature, plus engine run times.
Above all, watch how much time the engine spends cold: lots of short trips, with coolant never reaching 80 °C, wear the oil out faster and on a diesel cut regenerations short. The fix is an oil change with the right specification, followed by resetting the oil counter, which on many cars is done from the dashboard menu or with diagnostic equipment: if the counter isn't reset, the code returns even with fresh oil.
How serious is it, can you drive?
Severity is medium. If only the reset is missing, nothing is broken. If the oil really is worn out or diluted by diesel, it lubricates less well and the engine wears faster: drive gently and get the change done soon. With the level well above the maximum, it's better not to use the car until the oil has been changed.
Read P253F on your car
With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.
Get DrivePulseWhat it means
The ECU keeps track of how the engine works: revs, temperatures, cold starts, short trips, and on diesels the DPF regenerations too. From this it estimates how worn the oil is. Some cars also have a sensor that measures its quality.
With P253F the estimate has reached the limit. The most common case isn't a fault at all: the oil was changed, but nobody reset the indicator, and the ECU keeps counting on the old oil.
Symptoms
- Engine light on, often with a service message on the dashboard.
- No change in how the car drives, in most cases.
- On some models reduced power until the oil is changed.
- On diesels, sometimes, the oil level on the dipstick higher than usual.
Most likely causes, in order
- The indicator not reset after the last oil change.
- The oil genuinely at the end of its life, perhaps sooner than expected because of many short trips or heavy loads.
- Diesel in the oil on DPF diesels: when regenerations are often interrupted, part of the fuel injected to heat the exhaust ends up in the sump and dilutes the oil.
- The oil quality or temperature sensor, more rarely.
What to check before the garage
- When the last change was done: if it's recent, resetting the indicator from the instrument cluster menu, as the owner's manual explains, or with the garage's tool is almost always enough.
- On diesels, check the dipstick with the engine off and the car level: if the level rises instead of falling, there's diesel in the oil.
- If the oil smells of diesel or is very thin, don't wait for the due date: it needs changing now.
At the garage: what to ask for
An oil and filter change with oil of the specified grade, an indicator reset and, on diesels where the level was rising, a check of the DPF regenerations to find out why they're being interrupted.
What DrivePulse shows
DrivePulse reads P253F and its card reminds you that if the oil was changed recently, it's almost always just the indicator reset that's missing; it also tells you whether the code is pending or confirmed.
On suitable cars the DPF status shows the regenerations, and DrivePulse warns you when one is interrupted halfway: if that happens often, it's a sign fuel may be getting into the oil. Among the maintenance deadlines you can set the next oil change.
Frequently asked questions
Can I drive with P253F?
Yes, gently. If the oil is old or the level on the dipstick is rising, get it changed soon.
I've just changed the oil, why does it appear?
Almost always because the indicator wasn't reset. It's reset from the instrument cluster menu or with the garage's tool.
Why is the oil level rising?
On diesels with a DPF it can be fuel getting into the oil after interrupted regenerations. In that case the oil must be changed right away.
Related codes
Related guides
- Buying a used car? What to check: a code cleared just before the sale shows up in the distance driven since the last clear.
What you need to read it
All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.
DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.