EN ▾
EnglishItalianoDeutschFrançaisEspañolPortuguêsČeštinaPolskiMagyarRomână
Download
  1. DrivePulse
  2. Fault codes
  3. Accelerator, idle and brake
  4. P0507

P0507: idle air control system RPM higher than expected

Watch idle speed with the engine warm and all loads off: with P0507 it stays 100 to 200 rpm or more above target. If the throttle is almost closed and revs stay high, air is getting in elsewhere, for example a vacuum hose or the brake servo. You can drive normally, but fix it: it uses more fuel.

Get DrivePulse

What to look at in live data

Watch idle rpm with the engine warm, coolant above 80 °C and every load switched off (air conditioning, lights, rear window heater): it usually sits between 650 and 850 rpm, but the right value depends on the car. With P0507 it stays 100 to 200 rpm or more above what the ECU wants. Watch throttle position and calculated load too: if the throttle is almost closed and rpm stays high, air is getting in somewhere else.

The typical case is a leak after the throttle: a loose vacuum hose, the brake servo, the intake manifold gasket. Then the mass air flow sensor, if fitted, reads little air for that rpm and the fuel trims rise. If instead coolant temperature stays low or jumps around, the ECU holds a high idle because it thinks the engine is cold: the culprit is the temperature sensor or the thermostat.

How serious is it and can you drive?

Severity is low. You can drive normally. A high idle uses a little more fuel and, with an automatic gearbox, makes holding the car at a standstill harder work. It's worth fixing, not least because the air leak behind P0507 can eventually bring P0171.

Read P0507 on your car

With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.

Get DrivePulse

What it means

At idle the ECU has a target speed and reaches it by metering air. If the engine runs faster, it closes a little more. With P0507 it says it has closed to the limit and idle speed is still above target: more air is getting in than it controls.

Symptoms

  • The engine stays revved up at idle, even when warm.
  • A louder engine at a standstill.
  • With an automatic gearbox, the car creeps harder at a standstill in D.
  • Slightly higher fuel consumption in town.

Most likely causes, in order

  • An air leak: a loose or cracked vacuum hose, a gasket, the brake servo hose. It's the number one cause.
  • No relearn after cleaning the throttle body or disconnecting the battery.
  • The fuel vapour purge valve stuck open, letting in air and vapour.
  • A throttle that doesn't close fully, from deposits or a mechanical problem.

What to check before the garage

  • Listen at idle: a hiss near the intake is nearly always an air leak.
  • Have you just cleaned the throttle body or disconnected the battery? It needs a relearn: on some cars idling for a few minutes is enough, on others it takes the tool.
  • Check that the oil filler cap and the hoses around the intake manifold are in place.

At the garage: what to ask for

A smoke test for air leaks and a throttle relearn. If idle stays high, a check of the purge valve and of throttle closure.

What DrivePulse shows

DrivePulse reads P0507 and opens its card, with the two most common clues: a hiss at idle and a relearn after cleaning. The live Dashboard shows idle revs with a warm engine, and in Health the engine mixture: a strongly positive correction at idle strengthens the air leak theory.

Frequently asked questions

Can I drive with P0507?

Yes, normally. It's still worth fixing: it uses more fuel and the air leak can get worse.

Why did it appear after cleaning the throttle?

Because the ECU had learnt the dirty throttle. Once clean, the closed position changes and a relearn is needed.

How is it related to P0171?

The same air leak that raises idle makes the mixture lean. That's why the two codes often appear together.

Does a high idle harm the engine?

Not much in itself, but it uses more fuel and, if the cause is an air leak, the mixture at idle is lean. With an automatic gearbox, the brakes also work harder to hold the car at a standstill.

Related codes

Related guides

What you need to read it

All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.

DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.

← All codes