EN ▾
EnglishItalianoDeutschFrançaisEspañolPortuguêsČeštinaPolskiMagyarRomână
Download
  1. DrivePulse
  2. Fault codes
  3. Mixture and intake air
  4. P0171

P0171: system too lean, bank 1

Look at the fuel trims with the engine warm: together above 10% means the ECU is adding fuel. If they are high at idle and drop at about 2,500 rpm, air is getting in without passing the mass air flow sensor; if they stay high, check fuel delivery. You can drive gently, but find the cause soon.

Get DrivePulse

What to look at in live data

Look at the bank 1 short and long term fuel trims with the engine warm. Added together, above 10% means the ECU is adding fuel because it sees a lean mixture; at around 20 to 25%, depending on the car, the code appears.

Then compare idle with about 2,500 rpm in neutral. If the trim is high at idle and drops as revs rise, it is almost always air getting in without passing the mass air flow sensor: a vacuum hose, the intake manifold gasket, the crankcase ventilation valve. If it stays high or grows with load, look at fuel delivery (pump, filter, injectors) or a mass air flow sensor that reads less air than there really is. The comparison under load is done on the move, with the phone in the hands of the person in the passenger seat.

How serious is it and can you drive?

Severity is medium. You can drive gently, but it's not worth leaving it for months: a lean mixture makes combustion run hotter, and in the long run misfires and catalytic converter damage follow. If the check engine light flashes or the car jerks badly, ease off and stop as soon as you can.

Read P0171 on your car

With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.

Get DrivePulse

What it means

An engine runs well with a precise ratio of air to fuel. The oxygen sensor in the exhaust checks whether the ratio is right, and the ECU adjusts the fuel to match. This adjustment is called fuel trim. If keeping the mixture right means adding too much fuel, past the limit the ECU allows itself, it stores P0171: lean mixture.

Bank 1 is the side of the engine with cylinder number 1. Inline engines only have one bank. If P0174 shows up too, the same problem on bank 2, the cause is nearly always shared by both sides: a big air leak, the air mass sensor or not enough fuel.

Symptoms

  • Rough or hunting idle.
  • Hesitation or flat spots when you accelerate, sometimes a jerk.
  • Often no symptoms at all: only the light comes on.
  • Over time, misfires (P0300), because a very lean mixture burns badly.

Most likely causes, in order

  • An air leak: a cracked vacuum hose, a loose duct after the air sensor, the intake manifold gasket, the crankcase breather valve. It's the number one cause.
  • A dirty air mass sensor that measures less air than is really coming in.
  • Not enough fuel: clogged filter, tired pump, low pressure.
  • Dirty injectors spraying less than they should.
  • An exhaust leak before the oxygen sensor, which lets air in and fools the reading.

What to check before the garage

  • With the engine idling, listen: a hiss near the intake is nearly always an air leak.
  • Make sure the oil filler cap and the dipstick are properly seated: otherwise the engine sucks air through there too.
  • Look at the hoses and ducts after the air filter: cracks, loose clamps, swollen or hardened pipes.
  • Clean the air mass sensor with the dedicated spray, without touching the element. Never use compressed air.

At the garage: what to ask for

The quickest test is a smoke test: harmless smoke is blown into the intake and you see straight away where it comes out. If there are no leaks, the next steps are the air mass sensor and fuel pressure, measured with a gauge.

What DrivePulse shows

DrivePulse reads P0171 and opens its card with the causes in order and the checks. In Health you find the engine mixture, with the long-term fuel trim: if it's strongly positive, the engine is running lean.

A useful trick: in the live data, watch the short and long-term fuel trims at idle and then at about 2,500 rpm. If they are high at idle and return to normal as revs rise, it's nearly always an air leak. If they stay high everywhere, suspect the fuel supply or the air sensor.

Frequently asked questions

Can I drive with P0171?

Yes, gently. It's worth finding the cause soon though: running lean for a long time leads to misfires and can ruin the catalytic converter.

Is the oxygen sensor to blame?

Rarely. The sensor usually reports a real problem correctly. Replacing it before looking for an air leak is the most common way to spend money without fixing anything.

What does it mean if I also have P0174?

That the same problem is on both sides of the engine. Then the cause is shared: a big air leak, the air mass sensor or fuel pressure.

Related codes

Related guides

What you need to read it

All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.

DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.

← All codes