What to look at in live data
Misfires show best in the per-cylinder counters, which many cars report in the on-board test results (mode 06). If the misfires gather on one cylinder, suspect the plug, coil or injector of that cylinder: moving the coil to the next cylinder and seeing whether the problem follows it is the simplest test.
If they are spread over all cylinders, the cause is shared: a lean mixture (check the fuel trims), low fuel pressure, a vacuum leak or an EGR valve that stays open. An unsteady idle is another sign to watch.
Read P0300 on your car
With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.
Get DrivePulseWhat it means
P0300 means random misfires on several cylinders. The ECU measures the speed of the crankshaft on every turn. When a combustion is missed, the crankshaft slows down for an instant, and the ECU notices.
Codes P0301 to P0306 point to the exact cylinder. P0300 means the misfires are on several cylinders, or that the ECU can't tell which one.
If the check engine light flashes
Fuel that doesn't burn in the cylinder reaches the catalytic converter very hot and can melt it within a few miles. Ease off straight away, don't accelerate hard and stop as soon as you can.
Symptoms
- Vibration at idle, felt through the steering wheel and the seat.
- Jerks and flat spots under acceleration, especially uphill or at full load.
- Loss of power and higher fuel consumption.
- A smell of petrol from the exhaust.
Most likely causes, in order
- Worn spark plugs or coils.
- Poor fuel or water in the tank.
- Low fuel pressure.
- An air leak in the intake, letting in air that isn't measured.
- In the worst case, low compression in one or more cylinders.
What to do
- Think about when the spark plugs were last changed. Past roughly 60,000 km (about 40,000 miles) they are the first suspect.
- Try a tank of fuel from a different station.
- If the misfires continue, go to a garage without putting it off. Every mile with a misfire stresses the catalytic converter.
When to see a mechanic
- Straight away, if the light flashes.
- Soon, if the vibration continues or the code returns after a different tank of fuel.
- If P0420 appears together with P0300: the misfires have already started damaging the catalytic converter.
What DrivePulse shows
DrivePulse reads the code and opens the P0300 card. It tells you whether you can drive, the most likely causes and what to do, with the warning about a flashing light. It shows whether the light is on and, when the car reports it, how far you have driven with the light on.
When the ECU exposes its test results, DrivePulse shows misfires cylinder by cylinder. It's the quickest way to tell whether the problem is on one cylinder, and so a plug or a coil, or on all of them. In Health the engine mixture helps you spot an air leak.
Frequently asked questions
Can I drive with P0300?
If the light is steady and the car runs smoothly, gently as far as the garage. If the light flashes or the car shakes badly, no: stop, because the catalytic converter is damaged quickly.
Should spark plugs be changed all together?
Yes, usually all together. Coils are replaced only if faulty. A garage trick is to swap two coils: if the misfire follows the coil, the coil is the culprit.
What about cars on LPG or CNG?
Spark plugs work harder and need changing more often than the handbook says for petrol alone. Misfires are one of the first signs of tired plugs.
Related codes
Related guides
- Buying a used car? What to check: a code cleared just before the sale shows up in the distance driven since the last clear.
What you need to read it
All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.
DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.