EN ▾
EnglishItalianoDeutschFrançaisEspañolPortuguêsČeštinaPolskiMagyarRomână
Download
  1. DrivePulse
  2. Fault codes
  3. Timing and position sensors
  4. P0016

P0016: crankshaft/camshaft position correlation, bank 1

The useful value is variable valve timing, requested and actual, which many cars only show in manufacturer data: if the actual angle is several degrees off even at warm idle, the chain or belt may be stretched or have jumped a tooth. Drive only to the garage, without loading the engine.

Get DrivePulse

What to look at in live data

The useful value is variable valve timing: the camshaft angle the ECU asks for and the actual one. Many cars show it only in manufacturer data, not in the standard OBD2 values.

With the engine warm and at idle, actual should stay close to requested. If it is several degrees off already at idle, the chain or belt may be stretched or have jumped a tooth: better not to keep driving. If the gap shows up only as revs change, look at the cam phaser and its solenoid valve, and at the oil level and condition, which the phaser depends on.

How serious is it and can you drive?

Severity is high. If the cause is oil or a sensor, the engine isn't at immediate risk. If the timing drive has stretched and jumps a tooth, on many engines the valves can hit the pistons, and the damage becomes serious. Since the code alone can't tell you which it is, only drive as far as the garage and get it seen soon.

Read P0016 on your car

With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.

Get DrivePulse

What it means

The crankshaft and camshaft turn linked by the timing drive, a chain or a belt. Two sensors measure the position of each, and the ECU checks that the angle between them stays correct. With P0016 it says that, on bank 1 and for the camshaft labelled A (usually the intake one), the angle is out of limits.

Many modern engines move the camshaft on purpose with a cam phaser, driven by oil. That's why oil matters so much: a phaser that doesn't get enough oil, or sticks, shifts the timing just like a stretched chain.

Symptoms

  • Longer cranking than usual, sometimes the car won't start.
  • Rough idle and less power.
  • A metallic chain rattle for a few seconds on a cold start.
  • Often just the light, at first.

Most likely causes, in order

  • Low, old or wrong-spec oil, which makes the cam phaser work badly.
  • The valve that controls the phaser, stuck or dirty.
  • A worn cam phaser.
  • A stretched chain, a weak tensioner or, on belts, a jumped tooth.
  • A sensor for crankshaft or camshaft position, or its wiring.

What to check before the garage

  • The oil level, with the engine cold and the car level. If it's low, top up with the oil spec shown in the handbook.
  • When the oil was last changed. Very old oil is one of the most common causes.
  • On a cold start, listen to the first few seconds: a rattle or chain noise that then fades is an important clue to pass on to the garage.
  • Don't start and stop the engine several times to see if it goes away: if the chain is stretched, every cold start puts it to the test.

At the garage: what to ask for

A reading of actual and requested cam timing, a check of the phaser control valve and, if needed, a measurement of chain stretch. If the chain is replaced, the tensioner and guides are usually done at the same time. Sensors come last, once the timing checks out.

What DrivePulse shows

DrivePulse reads P0016 and opens its card, with the warning to take it seriously and not to restart the engine repeatedly if you hear chain noise. It tells you whether the code is pending or already confirmed: a pending P0016 that only shows up when cold is useful information to take to the garage.

If misfires or mixture faults appear at the same time, the code list shows them all, and Health helps you see whether the engine runs well after the repair.

Frequently asked questions

Can I drive with P0016?

Only as far as the garage, without straining the engine. Until you know whether the cause is oil, a sensor or the chain, long trips aren't a good idea.

Can an oil change be enough?

Sometimes, if the oil was very old, low or the wrong spec. If the code returns after the change, the timing drive needs checking.

What's the difference between P0016, P0017 and P0018?

They describe the same correlation for different camshafts or banks. The reasoning about causes is the same.

Related codes

Related guides

What you need to read it

All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.

DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.

← All codes