What to look at in live data
P0009 says the crankshaft position and the bank 2 camshaft position are no longer in the right relationship: it is the twin of P0008, which concerns bank 1. Timing can't be read directly in the standard data, but if the car reports requested and actual camshaft angle, watch bank 2 with the engine warm at idle: a fixed offset even with the phaser at rest means the base timing has shifted.
The most common cause is a stretched timing chain, especially if P0008 or the correlation codes (P0016 to P0019) appear too: then the problem is shared by both banks. If the code concerns bank 2 alone, look also at the tensioner and the secondary chain on that bank, where there is one. Old oil or a low level speed up the wear: late oil changes are often part of these engines' history.
How serious is it, can you drive?
It depends. If the engine runs smoothly, drive gently to the garage and don't put it off: a stretched chain can jump a tooth, and on many engines that damages the valves. If the engine shakes badly, makes metallic noises or loses power, stop somewhere safe.
Read P0009 on your car
With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.
Get DrivePulseWhat it means
The crank and cam sensors tell the ECU where the crankshaft and camshafts are. On a healthy engine the gap between the two signals always stays the same, apart from the corrections made by the cam phasers.
With P0009 the ECU measures that on bank 2 this gap has changed beyond the limit: the camshafts are advanced or retarded from where they should be, and the phasers can't make up for it.
What bank 2 is
On V engines, such as many six- and eight-cylinder units, the cylinders sit in two rows called banks. Bank 1 is the one with cylinder 1; bank 2 is the other row. That's why P0009 only appears on V engines: an inline engine has just one bank.
It often appears together with P0008, the same code for bank 1. When both banks are out of time together, suspicion falls on what they share, such as the main chain.
Symptoms
- Check engine light on, sometimes with nothing else.
- Chain noise, a sort of rattle, for a few seconds on a cold start.
- Uneven idle, loss of power or longer cranking.
Most likely causes, in order
- A stretched timing chain, along with worn tensioners and guides.
- The wrong oil level or grade, or oil changes too far apart: chain, tensioners and phasers all work with oil.
- A bank 2 cam phaser that stays stuck.
- A faulty cam or crank sensor, or a corroded connector.
- A jumped tooth after work on the timing.
What to check before the garage
- With the engine cold and the car level, check the oil level.
- Look in the service book for the specified oil and when it was last changed.
- Listen to the engine in the first seconds after a cold start: a metallic noise that then fades points to the chain.
At the garage: what to ask for
A live reading of camshaft timing against the crankshaft, bank by bank, and a check of the oil level and grade. If the deviation is large, the timing is inspected. In order of cost: correct oil, sensor or connector, cam phaser, chain with tensioners and guides.
What DrivePulse shows
DrivePulse reads P0009 and opens the engine card, which tells you to check oil and coolant with the engine cold, to note when it happens and to stop if the engine shakes or makes metallic noises; it also says whether the code is pending or confirmed.
If P0016, P0341 or P0335 appear too, DrivePulse lists them together: between them they help tell whether the problem is the timing or a sensor.
Frequently asked questions
Can I drive with P0009?
If the engine runs smoothly, gently and as far as the garage, without putting it off. If it shakes or makes metallic noises, stop somewhere safe.
Why only bank 2?
Because the code concerns a V engine and checks the second row of cylinders. If P0008 is there too, both banks are out of time.
Is it always the chain?
No: sometimes it's wrong or low oil, a cam phaser or a sensor. The timing reading at the garage shows how big the shift is.
Related codes
Related guides
- Buying a used car? What to check: a code cleared just before the sale shows up in the distance driven since the last clear.
What you need to read it
All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.
DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.