EN ▾
EnglishItalianoDeutschFrançaisEspañolPortuguêsČeštinaPolskiMagyarRomână
Download
  1. DrivePulse
  2. Fault codes
  3. Timing and position sensors
  4. P0341

P0341: camshaft position sensor range/performance

The camshaft signal arrives, but with extra, missing or misplaced pulses. It can be a dirty sensor, or a timing drive that has developed slack.

Get DrivePulse

What to look at in live data

The camshaft sensor has no value of its own among the standard OBD2 data, but its effects show. Watch engine rpm while cranking and at idle: if the engine turns over for a long time before it fires, or rpm has small jolts for no reason, the phase signal is arriving noisy. On engines with variable valve timing, if the car reports requested and actual camshaft angle, the two should match with the engine warm.

If the code comes with the timing ones (P0011, P0014) or with the crankshaft correlation code (P0016), suspect a stretched timing chain or belt, or one that has jumped a tooth, before the sensor. If it is on its own and comes and goes, look at the connector and wiring near the sensor, which live with heat and vibration; a damaged reluctor wheel sets the same code.

How serious is it and can you drive?

Severity is medium. If the sensor is the cause, you can drive gently to the garage. If the timing drive is old or you hear chain noise, don't put it off: a chain that jumps a tooth can seriously damage the engine.

Read P0341 on your car

With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.

Get DrivePulse

What it means

The ECU constantly compares the camshaft signal with the crankshaft signal: on every turn the pulses must arrive in the same place. With P0341 it says the signal is there but irregular: missing pulses, extra pulses or pulses outside the window where they should fall.

The difference from P0340 matters. There the signal is missing, and it's nearly always the sensor or its wiring. Here the signal is present but doesn't add up, and besides the sensor the timing drive can be involved.

Symptoms

  • Long cranking.
  • Jerks and a rough idle.
  • Loss of power.
  • Sometimes chain rattle when cold, if the timing drive is the cause.

Most likely causes, in order

  • Metal debris on the sensor's magnetic tip, disturbing the signal.
  • The sensor starting to fail, sometimes only when hot.
  • Wiring routed near ignition leads or with damaged insulation, picking up interference.
  • Slack in the timing drive: a stretched chain, weak tensioner, a belt that has jumped a tooth.
  • A damaged reluctor on the camshaft.

What to check before the garage

  • Read all the codes: if P0016 or a P0011 is there too, suspicion moves to the timing drive and the oil.
  • Listen to the first seconds after a cold start: a chain rattle is an important clue.
  • Check the oil level.

At the garage: what to ask for

Cleaning the sensor and checking its signal alongside the crankshaft signal, which shows straight away if the pulses are out of place. If the sensor is fine, a timing and chain stretch check.

What DrivePulse shows

DrivePulse reads P0341 and opens its card, with the advice to have the timing drive checked if it's old. It tells you whether the code is pending or confirmed and shows the related codes, P0016 and P0011 first.

In Health, the mixture and, when the ECU exposes them, misfires per cylinder help you see how badly the engine is running.

Frequently asked questions

Can I drive with P0341?

Gently, yes, if it's on its own and you hear no new noises. If it comes with P0016 or chain noise, only to the garage.

Can cleaning the sensor be enough?

Sometimes: metal filings stuck to the tip disturb the signal. If the code returns, the timing drive gets checked.

What's the difference from P0340?

P0340 says the signal is missing. P0341 says it's there but irregular or out of place, which is why the timing drive can be involved too.

Related codes

Related guides

What you need to read it

All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.

DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.

← All codes