What to look at in live data
With the engine warm and in closed loop (the fuel system status tells you), look at the two bank 1 oxygen sensors. The one before the catalytic converter, if it is a conventional sensor, keeps switching between about 0.1 and 0.9 V; the one after it should stay almost steady, usually between 0.5 and 0.8 V, because the converter evens out the swings. If the rear sensor copies the front one, the converter no longer stores oxygen. If the front sensor is a wideband type, it shows a lambda value close to 1.00 instead of switching.
Check the short and long term fuel trims too: if together they go beyond 10%, look for a mixture problem first, because that alone can set P0420. An exhaust leak ahead of the rear sensor skews its reading.
Can you drive?
Severity is medium. You can drive gently, but it's not worth ignoring it for months. If misfires are behind it, the converter will be ruined completely. If the check engine light flashes, stop as soon as you can.
Read P0420 on your car
With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.
Get DrivePulseWhat it means
The catalytic converter turns the most harmful exhaust gases into less harmful ones, and to do that it stores and releases oxygen. The ECU watches it with two sensors. The one before the converter swings up and down all the time, because the mixture is constantly adjusted. The one after it should stay fairly steady, a sign that the converter is doing its job. If the second one starts to mirror the first, the ECU decides the converter isn't storing enough oxygen and stores P0420.
Bank 1 is the side of the engine with cylinder 1. P0430 is the same code for bank 2.
Symptoms
- Usually none: the light comes on and the car drives as before.
- Sometimes a smell of rotten eggs from the exhaust.
- If the converter is badly clogged, a loss of power at higher revs.
- The car can fail the emissions test while the code is active.
Most likely causes, in order
- An aged catalytic converter, after many miles.
- A lazy rear oxygen sensor: a frequent false alarm, much cheaper than the converter.
- Misfires or a wrong mixture that have damaged it. They are the cause, the converter is the victim.
- An exhaust leak before the rear sensor, which lets air in and fools the reading.
- An engine burning oil or coolant, which coats the inside of the converter.
What to do
- Read all the codes. If there are misfires (P0300) or mixture faults (P0171), fix those first, or a new converter will be ruined too.
- Listen for a ticking noise from the exhaust on a cold start: it's the typical sign of a leak.
- Don't rush to replace the converter: first have the rear sensor and any exhaust leaks checked.
When to see a mechanic
- Soon, if the code is joined by misfires or mixture codes.
- Before an emissions test or MOT, because the active code can make the car fail.
- If you notice a loss of power at higher revs: the converter could be clogged.
What DrivePulse shows
DrivePulse reads the code and opens its card, with the most likely causes, symptoms, what to check and whether you can drive. In Health you find the engine mixture, with the long-term fuel trim, which helps you see whether the engine runs lean. When the ECU exposes them, it also shows misfires cylinder by cylinder.
In the live data, on cars that report them, you can watch the two oxygen sensors: the front one should swing and the rear one stay fairly steady. The Before the inspection card tells you how many monitors are ready, so you know whether the self-test has finished its checks after the repair.
Frequently asked questions
Is P0420 always the catalytic converter?
No. A lazy rear sensor or an exhaust leak can cause it, and both are much cheaper. Rule them out first.
Will clearing the code get me through the emissions test?
No. Clearing it resets the self-tests too, and with the monitors not ready the car can fail anyway. And the code comes back as soon as the ECU checks the converter again.
Do additives for the catalytic converter work?
They can help a converter that is only slightly fouled, but they don't repair one that is worn or melted. If there are misfires, the cause stays.
Related codes
Related guides
- Buying a used car? What to check: a code cleared just before the sale shows up in the distance driven since the last clear.
What you need to read it
All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.
DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.