EN ▾
EnglishItalianoDeutschFrançaisEspañolPortuguêsČeštinaPolskiMagyarRomână
Download
  1. DrivePulse
  2. Fault codes
  3. Timing and position sensors
  4. P0335

P0335: crankshaft position sensor circuit

Watch engine speed while cranking: if it stays at zero while the starter turns, the ECU does not see the crankshaft signal; if it drops to zero for an instant, the signal comes and goes. Drive only to the garage: the engine can stall on the move, making steering and brakes heavier.

Get DrivePulse

What to look at in live data

During cranking, watch engine revs in the data: if they stay at zero while the starter turns, the ECU is not seeing the crankshaft signal and the engine will not start. If revs show up in bursts, or drop to zero for a moment even at idle, the signal is cutting out intermittently.

If the engine stalls when hot, follow the revs as it happens, with the car stationary or with the phone held by the person in the passenger seat: if the value drops to zero at once, before the engine actually slows down, the signal disappeared first. If it restarts normally once the engine has cooled, a sensor that fails with heat is the first suspect.

How serious is it and can you drive?

Severity is high, because the engine can stall while you drive, and without the engine the steering and brakes get heavier. Only drive as far as the garage, avoiding motorways and overtaking. If the car has already stalled once when hot, don't count on it not happening again.

Read P0335 on your car

With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.

Get DrivePulse

What it means

The crankshaft sensor reads a toothed wheel, the reluctor, that turns with the crankshaft. From it the ECU works out engine speed and the exact position of the pistons, that is, when to make the spark and when to open the injectors. It's the most important signal in the engine. With P0335 the ECU says the signal is missing, interrupted or not the expected shape.

Symptoms

  • The engine stalls suddenly, often when hot, and restarts once it has cooled down.
  • The engine cranks but won't start.
  • Jerks and hesitation, a jumping rev counter.
  • While cranking, the car's rev counter stays at zero.

Most likely causes, in order

  • A failed sensor, often heat related: it works cold and stops when hot.
  • The connector or wiring, corroded, chewed by animals or rubbed through against the engine.
  • Metal debris on the sensor tip.
  • A damaged reluctor wheel, after work on the clutch or flywheel.

What to check before the garage

  • If you can see the sensor and its connector, check with the engine off that it's fully seated and the wires aren't damaged.
  • Note when it stalls: when hot, after how long, whether it restarts when cold. It's the most useful symptom for the garage.
  • If you've recently had work on the clutch or gearbox, say so: the sensor or the reluctor may have been disturbed.

At the garage: what to ask for

A check of the sensor signal with an oscilloscope or a resistance test, then the wiring and connector. The sensor is usually inexpensive; sometimes it's awkward to reach, and the labour outweighs the part.

What DrivePulse shows

DrivePulse reads P0335 and opens its card, with the warning that it can cause sudden stalling and the typical symptom of an engine that dies when hot. On the live Dashboard, engine speed comes from this very sensor: if it jumps or drops to zero while the engine is running, the signal is being lost.

DrivePulse also tells you whether the code is pending or confirmed: a pending P0335 that only shows up when hot is typical of a sensor on its way out.

Frequently asked questions

Can I drive with P0335?

Only as far as the garage. The engine can stall while driving, and without it steering and brakes get heavier.

Why does it only stall when hot?

Many sensors, as they start to fail, stop working with heat and come back once they cool. It's the most typical symptom of P0335.

Is the sensor expensive?

Usually not. Sometimes it's hard to reach and the labour costs more than the part, but it remains a modest repair.

Related codes

Related guides

What you need to read it

All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.

DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.

← All codes