What to look at in live data
If the car reports exhaust camshaft angle, watch requested and actual together with the engine warm: they should stay close, and when the request changes the actual value should follow within a second. With P0014 the actual angle goes past the requested one, or stays shifted when the request returns to rest.
The phaser moves with oil pressure, so the first suspect is the oil: low level, wrong grade or old oil. Next come the phaser solenoid, often with its small screen clogged, and a stretched timing chain, which shifts the base timing. If there are crank and cam correlation codes at the same time (P0016 to P0019), check the chain first.
How serious is it, can you drive?
Severity is medium. You can drive gently, but the engine performs worse and, if oil is low, top it up straight away: it's the same oil that lubricates the whole engine. If you hear the chain or P0016 appears, only drive as far as the garage.
Read P0014 on your car
With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.
Get DrivePulseWhat it means
Not every engine has this system: it takes variable timing on both camshafts. On the exhaust side, the phaser changes when the exhaust valves open, for more low-end torque, lower consumption and fewer emissions. It moves on oil pressure, metered by a solenoid.
With P0014 the ECU compares the requested position with the one read by the exhaust camshaft sensor and finds it too far advanced, or sees that the phaser isn't responding in time. It's the twin of P0011, which is about the intake camshaft.
Symptoms
- Engine light on, sometimes with the engine seeming normal.
- Rough idle, especially when the engine is warm.
- Less pick-up and slightly higher fuel consumption.
- A metallic rattle for a few seconds on a cold start.
Most likely causes, in order
- The oil: low level, old oil, or a grade different from the one in the handbook.
- The exhaust phaser solenoid, dirty or stuck, sometimes with its little screen clogged.
- The exhaust phaser worn or stuck.
- The chain and tensioner stretched or weak.
- The exhaust camshaft sensor, more rarely.
What to check before the garage
- The oil level, with the engine cold and the car on level ground.
- When the last oil change was done and with which oil: an oil different from the specified one is enough to confuse the phaser.
- Whether P0011 shows up too: when both sides are wrong, the most likely common cause is the oil or the chain.
- The noise on a cold start: if it lasts more than a few seconds or gets worse, have the chain checked soon.
At the garage: what to ask for
A check of oil level, type and pressure, then a test of the exhaust solenoid commanded by the tool, watching whether the camshaft moves. Only after that, a check of the phaser and chain. In order of cost: oil change, solenoid, phaser, timing chain, which is the most expensive item.
What DrivePulse shows
DrivePulse reads P0014 and opens its card, which tells you to start from oil level and quality; it also tells you whether the code is pending or confirmed and lists the other timing codes together, such as P0011 and P0016.
In the maintenance deadlines you can record the last oil change, so you always know when it was done and get reminded of the next one.
Frequently asked questions
Can I drive with P0014?
Yes, gently, checking the oil level straight away. If you hear chain noise or P0016 appears, only as far as the garage.
What's the difference from P0011?
They're the same check on two different camshafts: P0011 is the intake one, P0014 the exhaust one.
Does my engine have variable exhaust timing?
If the ECU sets P0014, yes: the code only exists on engines that also adjust the exhaust camshaft.
Related codes
Related guides
- Buying a used car? What to check: a code cleared just before the sale shows up in the distance driven since the last clear.
What you need to read it
All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.
DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.