What to look at in live data
The speed signal the ECU uses for ignition comes from the crankshaft sensor (on old cars, from the distributor). In the standard data, watch engine rpm at idle and while gently revving when parked: it should rise and fall smoothly. With P0321 the signal is erratic: rpm jumps by hundreds in an instant, or drops to zero for a moment, and the engine may jerk or stall.
If the jumps appear mainly when hot, the crankshaft sensor is the first suspect: many fail with heat and work again when cold. If they appear when you move the wiring, look for a chafed wire near a hot or moving part; a reluctor wheel with damaged teeth or coated in metal filings also gives a dirty signal. Then see whether the dashboard rev counter makes the same jumps: if it does, the signal is wrong at the source.
How serious is it and can you drive?
Severity is medium. If the engine runs normally, drive gently to the garage. If it has already cut out by itself, avoid motorways and busy roads: it could do it again at a dangerous moment.
Read P0321 on your car
With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.
Get DrivePulseWhat it means
The engine speed signal comes from the crankshaft sensor, the ignition or another control unit. The ECU knows revs change gradually: if it sees jumps, gaps or impossible values, it stores P0321.
Unlike P0322, which says the signal is missing altogether, here the signal is there but isn't clean. That's why the fault comes and goes, and you usually look for a loose contact or interference.
Symptoms
- Check engine or gearbox light on.
- Rev counter jumping or dropping to zero for a moment.
- Jerks, harsh shifts or the gearbox in limp mode.
- In the worst cases the engine cuts out suddenly.
Most likely causes, in order
- The speed sensor connector corroded or loose: the most common cause of an on-and-off signal.
- The signal wire squashed or running near the spark plug leads, which disturb it.
- The reluctor ring dirty, damaged or with a broken tooth.
- The sensor loose, too far from the reluctor ring, or failing when it warms up.
- An engine ground with a poor contact, or an add-on accessory causing interference.
What to check before the garage
- Note when it happens: when hot, over bumps, with the lights or an accessory on. These are valuable clues for the garage.
- Think about whether anything was fitted recently, such as an alarm, a camera or a charger: it can disturb the signal.
- With the engine off, if the sensor is reachable, check that the connector is properly latched.
A fault that comes and goes
An erratic signal is hard to catch at the garage, because with the engine cold and still everything often looks normal. That's why describing when it happens matters.
Garages look at the signal with an oscilloscope, hot as well, and move the wires with the engine running to see whether the signal drops out. A sensor replaced blindly often doesn't fix it.
At the garage: what to ask
Checking the signal with an oscilloscope, cold and hot, and moving the wires with the engine running. In order of cost: cleaning the connector, repairing the wiring or ground, a new sensor, and only last the reluctor ring.
What DrivePulse shows
DrivePulse reads P0321 and opens its card, with the advice to note whether the problem shows up when hot; it also tells you whether the code is pending or confirmed. If P0322 or P0335 appear too, you see them in the same list.
In the live Dashboard the revs come from the ECU: if they jump or drop to zero for a moment while the engine is running, the signal is being lost. While driving, the passenger watches them, not the driver.
Frequently asked questions
Can I drive with P0321?
If the engine runs normally, yes, gently to the garage. If it has already cut out by itself, avoid motorways and busy roads.
What's the difference from P0322?
P0322 says the engine speed signal is missing altogether. P0321 says it arrives but is erratic, with jumps or gaps: usually a loose contact or interference.
Why does the fault come and go?
Because it often depends on heat, vibration or a connector making contact only some of the time. That's why it's worth noting when it happens.
Related codes
Related guides
- Buying a used car? What to check: a code cleared just before the sale shows up in the distance driven since the last clear.
What you need to read it
All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.
DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.