What to look at in live data
With P0322 the speed signal doesn't arrive at all: usually the engine cranks but won't start, or cuts out suddenly while driving. In the standard data the test is simple: watch engine rpm while cranking. A turning starter brings the engine to 150 to 250 rpm, and that value should appear; if it stays at zero while the engine turns, the ECU can't see the sensor.
If the engine starts and cuts out now and then, watch rpm at the moment it dies (on the move, the phone stays with the person in the passenger seat): an instant drop to zero, not a gradual one, means the signal vanished rather than the engine losing power. The check is done with the engine off: crankshaft sensor connector, wires to the ECU, gap between sensor and reluctor wheel. A sensor that fails when hot often lets the engine restart after half an hour's rest.
How serious is it, can you drive?
Severity is medium, but it depends on what has already happened. If the engine runs normally, drive gently to the garage. If it has already cut out on its own, avoid motorways and busy roads: it could do it again at a dangerous moment.
Read P0322 on your car
With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.
Get DrivePulseWhat it means
The engine ECU, and on many cars the gearbox ECU too, receives a signal that says how fast the engine is turning. It comes from the crankshaft sensor, from the ignition or, on older cars, from the distributor. It's used for injection, ignition and gear changes.
With P0322 that signal's circuit gives nothing: the signal is missing altogether. It's a close relative of P0335, which is about the crankshaft sensor; on some cars both codes point to the same fault.
Symptoms
- Engine or gearbox light on.
- The engine won't start, or cuts out suddenly while you're driving.
- The rev counter jumps or drops to zero.
- Harsh gear changes, or the automatic gearbox in limp mode.
Most likely causes, in order
- The engine speed sensor connector or the ECU connector, corroded or loose.
- The signal wire broken, pinched or picking up interference.
- A failed crankshaft sensor, often only when it gets hot.
- The engine earth making poor contact.
- The reluctor ring dirty or damaged, or the sensor loose and too far from it.
What to check before the garage
- When it happens: if it's with a hot engine, the speed sensor is the first suspect.
- The rev counter: if it moves oddly while the engine is running, the signal is being lost.
- Accessories fitted recently, such as alarms or extra lights: their wiring can interfere with the signal.
- With the engine off, the sensor connector: pushed home, with no oil and no corrosion.
At the garage: what to ask for
A check of the engine speed signal with an oscilloscope, cold and hot, then a check of the sensor, wiring, connectors and earths. The part to replace is usually the sensor, which is cheap; the labour depends on where it's fitted.
What DrivePulse shows
DrivePulse reads P0322 and opens its card, with the advice to note whether the problem shows up when hot; it also tells you whether the code is pending or confirmed.
On the live Dashboard, engine speed comes from the ECU: if it jumps or drops to zero while the engine is running, the signal is being lost. If P0335 shows up too, DrivePulse lists them together.
Frequently asked questions
Can I drive with P0322?
If the engine runs normally, yes, gently as far as the garage. If it has already cut out on its own, avoid motorways and busy roads.
What's the difference from P0335?
P0335 is about the crankshaft sensor circuit. P0322 says the engine speed signal isn't arriving, whatever its source: on many cars it's the same fault.
Why does it only happen when hot?
Many speed sensors fail internally and stop working when they warm up. When cold they give a signal again, until the fault gets worse.
Related codes
Related guides
- Buying a used car? What to check: a code cleared just before the sale shows up in the distance driven since the last clear.
What you need to read it
All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.
DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.