EN ▾
EnglishItalianoDeutschFrançaisEspañolPortuguêsČeštinaPolskiMagyarRomână
Download
  1. DrivePulse
  2. Fault codes
  3. Automatic transmission
  4. P0726

P0726: engine speed input circuit range/performance

An automatic gearbox needs to know engine speed to decide when and how to change gear. With P0726 that signal is there, but it jumps or doesn't add up with everything else. The gearbox can turn harsh or go into limp mode.

Get DrivePulse

What to look at in live data

P0726 is usually stored by the transmission module: the engine speed signal it receives isn't plausible. In the standard data, watch engine rpm at idle and while gently raising revs when parked: it should be steady and follow the pedal without jumps. If you see gaps or spikes there too, the problem is in the crankshaft signal, and the engine ECU often has its own code (P0335, P0336) to start from.

If rpm is clean in the engine data, the signal goes wrong on its way to the transmission: a dedicated wire on some cars, the network between modules on others. In that case check the control module voltage and look for communication codes (the ones starting with U). The typical symptom is harsh or badly timed shifts, because the transmission doesn't really know how fast the engine is turning.

How serious is it, can you drive?

Severity is medium, and it depends on the symptoms. If the gearbox works properly, drive gently to the garage. If it's in limp mode, avoid motorways and long climbs in a single gear. If the engine has already cut out on its own, don't drive in fast traffic.

Read P0726 on your car

With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.

Get DrivePulse

What it means

The transmission control unit compares engine speed with the speed of the gearbox shafts: that's how it knows whether the internal clutches are slipping and when to shift. The engine speed figure comes from the crankshaft sensor, usually by way of the engine ECU.

With P0726 the signal isn't missing, but it's out of range or implausible: jumps, gaps, values that don't match road speed. When it's missing altogether the typical code is P0322 or P0335; P0726 is about a signal that's present but unreliable.

Symptoms

  • Gearbox or engine light on.
  • Harsh, late or badly timed gear changes.
  • The gearbox stays in one gear, usually third, in limp mode.
  • A jumping rev counter; sometimes the engine cuts out.

Most likely causes, in order

  • The engine speed sensor connector or the ECU connector, corroded or loose.
  • The signal wire damaged or picking up interference, for example from accessories fitted later.
  • A crankshaft sensor on its way out, often only when hot.
  • An engine or gearbox earth making poor contact.
  • The reluctor ring dirty or damaged.

What to check before the garage

  • Whether it only shows up once the engine is warm: that's typical of a speed sensor on its way out.
  • The rev counter while you drive: sudden jumps or drops confirm a disturbed signal.
  • Whether alarms, lights or other accessories were fitted recently, and where their wiring runs.
  • The battery and its terminals: an unstable voltage confuses both the engine and gearbox control units.

At the garage: what to ask for

A readout of the transmission control unit's memory as well as the engine's, a check of the engine speed signal with an oscilloscope, cold and hot, and a check of connectors and earths. The part is usually the speed sensor, which is cheap; it only costs more if the fault is in the wiring or a control unit.

What DrivePulse shows

DrivePulse reads P0726 and opens its card, with the advice to note whether the problem shows up when hot and to watch the rev counter; it also tells you whether the code is pending or confirmed.

On the live Dashboard you see engine speed: if it jumps at a steady speed, the signal is disturbed. In Health, the battery voltage helps rule out an unstable supply. If P0700 or P0335 show up too, DrivePulse lists them together. While driving, the passenger watches the screen, not the driver.

Frequently asked questions

Can I drive with P0726?

If the gearbox works properly, yes, gently as far as the garage. If it's in limp mode, avoid motorways and long climbs.

What's the difference from P0322?

P0322 says the engine speed signal isn't arriving. P0726 says it arrives but is out of range or implausible.

Why does the gearbox light come on for an engine problem?

Because the transmission control unit uses engine speed to change gear: if the figure is unreliable, it protects the gearbox and flags it.

Related codes

Related guides

What you need to read it

All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.

DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.

← All codes