EN ▾
EnglishItalianoDeutschFrançaisEspañolPortuguêsČeštinaPolskiMagyarRomână
Download
  1. DrivePulse
  2. Fault codes
  3. Automatic transmission
  4. P0720

P0720: output shaft speed sensor circuit

The automatic gearbox counts the revs of its output shaft with a sensor: by comparing them with the input revs it knows which gear it's in and when to shift. With P0720 that sensor's signal is missing or has impossible values. Often the speedometer goes haywire and the shifts turn strange.

Get DrivePulse

What to look at in live data

The output shaft speed sensor tells the transmission module how fast the output is turning, and from that which gear is engaged. In the standard data you see the effect through vehicle speed and engine rpm: on the move, with the phone in the hands of the person in the passenger seat, check that the ratio between rpm and speed stays consistent in each gear. With P0720 the transmission often shifts harshly, skips gears or stays in limp mode, and on some cars the speedometer can drop to zero.

If the car reports output shaft speed through the manufacturer's diagnostics, compare it with wheel speed: they should rise and fall together. A value that drops to zero for a moment means a bad contact, often in the connector on the transmission, dirty with oil; a value missing entirely means the sensor or a wire is open. Metal filings stuck to the sensor's magnetic tip also disturb the signal.

How serious is it and can you drive?

Severity is high. With the gearbox in limp mode the car moves, but it accelerates slowly and doesn't shift as it should: avoid motorways and overtaking and drive carefully only as far as the garage. If the speedometer isn't working, match your speed to the traffic around you and don't put off the repair.

Read P0720 on your car

With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.

Get DrivePulse

What it means

The sensor reads a toothed wheel on the shaft that leaves the gearbox towards the wheels. The gearbox control unit uses that signal to time the shifts and, on many cars, also to work out the speed on the speedometer.

With P0720 the sensor circuit has a fault: the signal is missing, cuts out or has impossible values. Without that figure the gearbox no longer knows how fast the car is going and often goes into limp mode, stuck in one gear.

Symptoms

  • Check engine or gearbox warning light on.
  • Speedometer stuck at zero or jumping, on many cars.
  • Harsh, late or early shifts.
  • Gearbox stuck in one gear (limp mode).
  • Cruise control that won't engage.

Most likely causes, in order

  • The sensor failed, or with its magnetic tip covered in metal filings.
  • The sensor connector oily or corroded.
  • The sensor wires broken or shorted, often where they run near the exhaust.
  • The toothed wheel damaged, which is rarer.

What to check before the garage

  • Notice whether the speedometer drops to zero or jumps right when the gearbox shifts oddly: together they confirm the lost signal.
  • Check the gearbox oil level, if your car has a dipstick and the handbook explains how.
  • Note when it happens: cold, hot, over bumps. It helps track down a wire that makes contact only now and then.

Speedometer and gearbox together

On many cars the speedometer takes its speed from this very sensor. That's why a haywire speedometer and wrong shifts at the same moment are the typical sign of P0720.

If P0500, the vehicle speed sensor, appears too, read the two codes together: on some cars the two signals are compared, and when one is missing the other code is set as well.

At the garage: what to ask

Reading the gearbox control unit's codes, checking the sensor signal with a tester while the wheels turn, and checking the wiring and connector. In order of cost: connector and wiring, a new sensor, and only then work inside the gearbox.

What DrivePulse shows

DrivePulse reads P0720 and opens its card with the most useful clue: a haywire speedometer and wrong shifts together confirm the fault. It also tells you whether the code is pending or confirmed.

In live data, on cars that report it, you'll find the speed read from the car: if it comes from this sensor, while driving the passenger sees it stay at zero or jump while the car moves steadily. If P0700 or P0500 show up too, DrivePulse lists them together.

Frequently asked questions

Can I drive with P0720?

Carefully and only as far as the garage: the gearbox often goes into limp mode, accelerates slowly and doesn't shift as it should. Avoid motorways and overtaking.

Why isn't the speedometer working?

On many cars the speedometer uses this very sensor's signal. When the sensor sends nothing, the speedometer stays at zero or jumps.

What's the difference from P0700?

P0700 only says the gearbox control unit has stored a fault. P0720 is one of the possible faults: the output speed sensor circuit.

Related codes

Related guides

What you need to read it

All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.

DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.

← All codes