What to look at in live data
P0700 on its own says little: it is the transmission control unit asking for the check engine light, and the code that explains the fault stays in its own memory. The first step is reading the transmission unit's codes, which do not always show up among the engine's standard OBD2 codes: write them down and take them to the garage.
In live data, while someone else drives and the phone is held by the person in the passenger seat, compare engine revs and speed in gear: if revs jump and speed does not follow, the transmission is slipping. If the car reports transmission fluid temperature, a very high value after an ordinary trip is another clue to pass on.
How serious is it and can you drive?
Severity is medium, but it depends on the real code. If the gearbox is in limp mode, drive gently to the garage, and avoid motorways if it's stuck in a low gear. If you feel strong slipping, hear new noises or smell burning, stop: a slipping gearbox wears out quickly.
Read P0700 on your car
With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.
Get DrivePulseWhat it means
On cars with an automatic, automated manual or dual-clutch gearbox, the gearbox has its own control unit. When it finds a fault that could affect emissions or driving, it asks the engine ECU to turn on the light. The engine ECU then stores P0700, which only means: the transmission has a problem, look in its memory.
That's why P0700 alone doesn't tell you what to repair. The code that matters is the one stored in the transmission control unit, often another P07xx: speed sensors, solenoids, the torque converter clutch, the gear selector position.
Symptoms
- Harsh, late or jerky shifts.
- The gearbox stays in one gear (limp mode), usually third or second.
- Revs rise without the car speeding up, as if it were slipping.
- Sometimes no symptoms, just the light.
Most likely causes, in order
- Transmission fluid that is low, old or the wrong spec. On automatics and dual-clutch boxes it's the most forgotten maintenance item.
- A gearbox sensor, for speed or temperature, or its connector.
- A solenoid that controls pressures and engagement.
- The wiring or the main gearbox connector, sometimes with fluid wicking inside.
- An internal mechanical fault, less common and checked last.
What to check before the garage
- When was the transmission fluid last changed? If you don't know, or it was many miles ago, that's the first thing to ask.
- Look under the car for reddish or dark fluid stains near the gearbox.
- Note when it happens: cold, warm, in one particular gear. It shortens the diagnosis at the garage.
- A weak battery and corroded grounds can confuse control units: if the car is also slow to start, check the battery first.
At the garage: what to ask for
A readout of the transmission control unit's memory, not just the engine's. With the real code, they check fluid level and condition, then the solenoids and sensors it points to. On many automatics a proper fluid change, with the filter, fixes more than you'd expect.
What DrivePulse shows
DrivePulse reads P0700 from the OBD port and opens its card, which makes the key point straight away: you need a readout of the transmission control unit. Standard OBD often doesn't expose it, so the detail comes from a garage tool.
If another transmission code appears alongside P0700, DrivePulse shows it with its own card. And in Health the battery voltage helps rule out the battery as the cause.
Frequently asked questions
Does P0700 mean the gearbox is broken?
No. It means the transmission control unit has stored a fault. It could be a sensor or fluid that needs changing: you need to read the real code.
Can I drive with P0700?
Gently, yes, to the garage. If the gearbox slips, makes new noises or smells burnt, it's better to stop.
Does clearing the code help?
No. If the fault is still there, the transmission control unit stores it again and the light comes back. Meanwhile you lose the information the garage needs.
Related codes
Related guides
- Buying a used car? What to check: a code cleared just before the sale shows up in the distance driven since the last clear.
What you need to read it
All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.
DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.