EN ▾
EnglishItalianoDeutschFrançaisEspañolPortuguêsČeštinaPolskiMagyarRomână
Download
  1. DrivePulse
  2. Fault codes
  3. Automatic transmission
  4. P0748

P0748: pressure control solenoid A electrical

The solenoid that regulates fluid pressure in the gearbox has an electrical problem. Without that control shifts become harsh and the gearbox protects itself.

Get DrivePulse

What to look at in live data

The solenoid that regulates pressure in the automatic transmission has no value among the standard OBD2 data; some cars report its commanded current or pressure through the manufacturer's diagnostics. In the standard data you see the effect: watch engine rpm and road speed during gear changes, with the phone in the hands of the person in the passenger seat. With P0748 the transmission often goes into limp mode, holds one gear (often an intermediate one) and rpm climbs higher than normal for the same speed.

If the car reports transmission fluid temperature, keep an eye on it: the electrical fault often gets worse when hot, as the winding resistance changes or a cracked wire opens. The check is done with the engine off, at the transmission connector: solenoid resistance (often a few ohms) and continuity of the wires back to the module. Old or low fluid doesn't set this code on its own, but check it anyway before replacing parts.

How serious is it and can you drive?

Severity is high. Harsh shifts and limp mode strain the clutches and driveline, and a gearbox running without the right pressure gets damaged. Only drive as far as the garage, gently, and avoid motorways if it's stuck in a low gear.

Read P0748 on your car

With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.

Get DrivePulse

What it means

In an automatic gearbox, fluid pressure decides how firmly the internal clutches and brakes close, so how smooth or firm each shift is. A solenoid, controlled by the ECU, regulates it moment by moment. With P0748 the ECU says this solenoid's electrical circuit isn't responding as it should: open, shorted or out of range.

The letter A distinguishes this solenoid from similar ones in the same gearbox. The code is about the electrical circuit: the solenoid may have failed, but so may just its connection.

Symptoms

  • Harsh, clunky shifts, especially selecting D or R from standstill.
  • The gearbox stays in one gear (limp mode).
  • A delay when you select a gear.
  • It often appears together with P0700.

Most likely causes, in order

  • A failed solenoid, open or shorted inside.
  • Internal gearbox wiring, which works immersed in hot fluid.
  • The main gearbox connector, corroded or with fluid wicking inside.
  • Badly degraded transmission fluid, which makes the valves work poorly.

What to check before the garage

  • Look at the gearbox connector, if you can reach it, with the engine off: corrosion, fluid, a bent pin.
  • Check for fluid leaks from the gearbox.
  • Note whether the fault shows when cold or when warm: it helps spot a contact that opens with heat.

At the garage: what to ask for

A resistance measurement of the solenoid at the gearbox connector, a check of the wiring and of the fluid condition. On many gearboxes the solenoids are fitted as a pack, and the whole pack is replaced. A garage that works on automatic gearboxes is the better choice.

What DrivePulse shows

When the code reaches the OBD port, DrivePulse reads P0748 and opens its card, with the advice not to put it off. Electrical measurements on the solenoid and a full readout of the transmission control unit need a garage tool.

If P0700 appears too, DrivePulse shows them together: P0700 only says the gearbox has a fault, P0748 says which.

Frequently asked questions

Can I drive with P0748?

Only as far as the garage, gently. Harsh shifts and limp mode strain the gearbox, and the damage can grow.

Does the whole gearbox need replacing?

Almost never for this code. Usually the solenoid or the solenoid pack is replaced, after checking the connector and wiring.

How is it related to P0700?

P0700 is the code the engine ECU uses to turn on the light for the gearbox. P0748 is the specific fault stored by the gearbox.

Related codes

Related guides

What you need to read it

All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.

DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.

← All codes