EN ▾
EnglishItalianoDeutschFrançaisEspañolPortuguêsČeštinaPolskiMagyarRomână
Download
  1. DrivePulse
  2. Fault codes
  3. Automatic transmission
  4. P0705

P0705: transmission range sensor circuit

If the car reports the selector position read by the transmission unit, test it standing still with your foot on the brake: each position should appear as you see it on the dashboard, with no blanks or jumps. If it jumps or lags, the sensor is dirty or out of adjustment. Usually drivable with care; always use the handbrake when parked.

Get DrivePulse

What to look at in live data

If the car reports the selector position read by the transmission control unit, test it while parked: engine running, foot on the brake, move the lever slowly from P to D. Each position should appear in the data at the same moment you see it on the dashboard, with no blank values and no jumps between two positions.

If the value jumps, shows the wrong position or lags on the previous one, the sensor, often mounted on the outside of the gearbox, is dirty, out of adjustment or has a corroded connector. If the data is right but the car will not start in P or N, check the wiring between the sensor and the starter circuit too.

How serious is it and can you drive?

Severity is medium. You can usually drive, but carefully: if the ECU doesn't know where the selector is, it may engage a gear harshly or refuse to start. Don't leave the car on a slope relying on P alone: always use the handbrake as well until it's fixed.

Read P0705 on your car

With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.

Get DrivePulse

What it means

On automatics a sensor, sometimes called the range switch, reads the selector position: park, reverse, neutral, drive and so on. The ECU uses it to decide which clutches to engage, to switch on the reversing lights and to allow starting only in P or N. With P0705 it says the signal is missing, inconsistent or showing two positions at once.

Symptoms

  • The engine won't start in P but starts in N (or the other way round).
  • Reverse or drive doesn't engage first time, or engages late.
  • The reversing lights don't come on, or stay on.
  • The gear letter on the dashboard doesn't match the selector.
  • The gearbox goes into limp mode.

Most likely causes, in order

  • A worn range sensor or switch, with worn or dirty contacts.
  • The cable or linkage adjustment between selector and gearbox, out of adjustment.
  • The connector or wiring, often exposed to dirt and water under the car.
  • Fluid seeping into the sensor connector, on some gearboxes.

What to check before the garage

  • Try starting in P and in N: note which position doesn't work.
  • Move the selector slowly through the positions and watch whether the dashboard letter follows without jumps.
  • With someone behind the car, check that the reversing lights come on only in R.
  • If you can see the sensor connector, look for dirt or corrosion, with the engine off.

At the garage: what to ask for

A readout of the transmission control unit with the sensor values while the selector moves, then a check of the linkage adjustment. If the sensor is worn it gets replaced and set up. Often adjustment alone fixes it.

What DrivePulse shows

When the code reaches the OBD port, DrivePulse reads P0705 and opens its card, with the typical symptoms and the advice to try adjustment first. For the sensor values as you move the selector you need a garage tool that reads the transmission control unit.

DrivePulse also tells you whether the code is pending or confirmed: a pending P0705 that only shows up in the rain points to the connector.

Frequently asked questions

Can I drive with P0705?

Usually yes, carefully. Always use the handbrake when parked and get it checked soon, because the gearbox may engage harshly.

Does the sensor need replacing?

Not always. Adjusting the selector cable is often enough. If the sensor is worn it gets replaced, and then set up.

Why won't the car start in P but starts in N?

Because the sensor isn't reporting P properly, and for safety the ECU won't allow the engine to start. It's one of the typical symptoms of P0705.

Related codes

Related guides

What you need to read it

All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.

DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.

← All codes