What to look at in live data
The transmission range sensor tells the ECU where the lever is: P, R, N, D and the other positions. On many cars the lever position isn't among the standard OBD2 data, but some report it, and the manufacturer's diagnostics nearly always show it: if you can see it, move the lever slowly from P to D with the engine running and your foot on the brake, and check that each position appears at the right moment, with no jumps or in-between positions.
With P0706 the ECU sees signals that match no valid position, or that don't fit the gear the transmission actually detects: typical symptoms are an engine that won't start in P or N, reverse lights that don't come on, a transmission that goes into limp mode. Often the sensor sits on the transmission and shifts slightly with vibration: it should be adjusted before it is replaced. Water or oil in the connector gives the same picture.
How serious is it, can you drive?
Severity is high, because it concerns the gear position. If the dashboard shows the right position, drive gently to the garage. If it doesn't match, don't drive: the car could move when you don't expect it.
Read P0706 on your car
With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.
Get DrivePulseWhat it means
The range sensor sits on the gearbox and reads where the selector is: park, reverse, neutral or drive. The ECU uses it to allow starting only in P or N, to switch on the reversing lights and to choose gears.
With P0706 the signal from sensor A is out of range or implausible: for example it shows a position that doesn't exist or doesn't match what the ECU expects. That's different from P0705, which is an electrical fault in the same sensor's circuit.
Symptoms
- The engine won't start in P, but may start in N.
- The letter on the dashboard doesn't match the selector position, or flashes.
- The reversing lights don't come on.
- The gearbox goes into limp mode or won't engage a gear.
Most likely causes, in order
- The sensor needing adjustment, moved after work on the gearbox.
- The selector cable stretched or badly adjusted.
- The sensor connector, on the gearbox, corroded or oily.
- Worn internal contacts in the sensor.
- The wiring damaged near the gearbox.
What to check before the garage
- Try starting in P and in N and note whether anything changes.
- Move the selector slowly through every position, engine off and brake pressed, and watch whether the letter on the dashboard follows.
- Whether the gearbox was removed or repaired recently: a sensor that wasn't adjusted is the most likely cause.
- Always apply the handbrake before getting out.
At the garage: what to ask for
A live reading of the position the ECU sees while the selector is moved, then adjustment of the sensor or the selector cable. Only if that's not enough, a new sensor. Adjustment and cable are cheap; the sensor costs more, especially when it's mounted inside the gearbox.
What DrivePulse shows
DrivePulse reads P0706 and opens its card, with the P-and-N starting test and the warning not to drive if the letter on the dashboard doesn't match the selector; it also tells you whether the code is pending or confirmed.
If P0705 or P0700 show up too, DrivePulse lists them together. For the gearbox details you often need the transmission control unit read at a garage, because standard OBD doesn't always show it.
Frequently asked questions
Can I drive with P0706?
Only if the letter on the dashboard matches the selector, and gently as far as the garage. If it doesn't match, no: the car could move on its own.
What's the difference from P0705?
P0705 is an electrical fault in the sensor circuit. P0706 says the circuit works but the signal isn't believable.
Why does the car start in N but not in P?
Because the ECU only allows starting if the sensor confirms P or N. If it misreads P, it blocks starting there.
Related codes
Related guides
- Buying a used car? What to check: a code cleared just before the sale shows up in the distance driven since the last clear.
What you need to read it
All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.
DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.