What to look at in live data
Transmission fluid temperature isn't among the standard OBD2 data on every car, but many report it. If yours does, the simplest check is done cold: after a night parked it should be close to engine coolant and air temperature. With P0710 the value is impossible (often -40 °C or the top of the scale) or missing, which points to an open or shorted circuit.
With the engine running, transmission fluid temperature should rise slowly and steadily, usually staying a little below engine coolant on gentle trips (on the move, the person in the passenger seat follows the value). Without this data the ECU uses a substitute value: shifts may become harsh when cold or the converter may never lock up. The sensor often sits inside the transmission, on the solenoid harness: check the connector and cables before opening anything.
How serious is it, can you drive?
Severity is high, because the gearbox no longer knows its fluid temperature. You can drive gently only as far as the garage, avoiding towing, long climbs and sporty driving. If a gearbox overheating warning appears, stop and let it cool down.
Read P0710 on your car
With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.
Get DrivePulseWhat it means
The transmission control unit uses the fluid temperature to decide the pressure, the timing of shifts and when to lock the torque converter, and to protect the gearbox when the fluid gets too hot.
With P0710 the problem is electrical: the signal is missing, shorted or outside the values the circuit can give. That's different from P0711, where the circuit works but the temperature read isn't believable. On many gearboxes the sensor sits inside, on the electrical plate, immersed in fluid.
Symptoms
- Harsher or later shifts, especially when cold.
- The gearbox in limp mode, stuck in one gear.
- A possible gearbox overheating warning on the dashboard.
- The converter not locking up, with slightly higher fuel use.
Most likely causes, in order
- The gearbox connector corroded or with fluid inside.
- The gearbox's internal wiring damaged.
- A failed sensor, often mounted on the internal electrical plate.
- Transmission fluid low, old or the wrong type, which damages the contacts over time.
What to check before the garage
- Whether there are drops of reddish or dark fluid under the car, near the gearbox.
- When the transmission fluid was last changed.
- Whether gearbox overheating warnings appear, and in what conditions: hills, towing, traffic.
- The main gearbox connector, if you can reach it: fluid on the contacts is a strong clue.
At the garage: what to ask for
A live reading of the transmission fluid temperature, compared with the engine temperature when cold, a measurement of the sensor at the connector and a fluid level check using the proper procedure, at temperature. In order of cost: connector cleaning, sensor, wiring or internal plate, which are the most expensive items.
What DrivePulse shows
DrivePulse reads P0710 and opens its card, with the advice to avoid towing and long climbs and to stop if the gearbox overheating warning appears; it also tells you whether the code is pending or confirmed.
If P0700 or P0711 show up too, DrivePulse lists them together. For gearbox details you often need the transmission control unit read at a garage, because standard OBD doesn't always show it.
Frequently asked questions
Can I drive with P0710?
Gently and only as far as the garage, with no towing or long climbs. If a gearbox overheating warning appears, stop and let it cool down.
What's the difference from P0711?
P0710 is an electrical fault in the sensor circuit. P0711 says the circuit works but the temperature read isn't believable.
Is changing the transmission fluid enough?
Rarely, because P0710 is an electrical problem. But old fluid should be changed anyway, and a connector full of fluid needs cleaning or replacing.
Related codes
Related guides
- Buying a used car? What to check: a code cleared just before the sale shows up in the distance driven since the last clear.
What you need to read it
All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.
DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.