EN ▾
EnglishItalianoDeutschFrançaisEspañolPortuguêsČeštinaPolskiMagyarRomână
Download
  1. DrivePulse
  2. Fault codes
  3. Automatic transmission
  4. P0741

P0741: torque converter clutch performance or stuck off

While someone else drives on the motorway and the passenger holds the phone, watch engine revs at steady speed: with the converter locked they stay put. If they rise and fall by 100 to 200 rpm on their own, the lock-up is not holding; old or hot transmission oil is a common cause. You can drive, but do not leave it for months.

Get DrivePulse

What to look at in live data

While someone else drives and the phone is held by the person in the passenger seat, watch engine revs at a steady speed on the motorway: with the converter locked they hold still, and at the same speed they are a little lower than with the converter unlocked. If they rise and fall by 100-200 rpm on their own with nothing changing, the lock-up is not holding.

If the car reports torque converter slip, the difference between engine speed and transmission input speed, it should be close to zero with lock-up engaged. Check transmission fluid temperature too: old or overheated fluid makes the lock-up slip, which is why the garage often starts with the fluid.

How serious is it and can you drive?

Severity is medium. You can drive, but it gets worse: a slipping clutch heats the fluid, and hot fluid breaks down and harms other parts of the gearbox. It's worth acting soon, while a fluid change may still be enough.

Read P0741 on your car

With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.

Get DrivePulse

What it means

The torque converter links engine and gearbox through fluid, which lets you pull away without a clutch pedal. Fluid slips, though, and at a steady speed that wastes energy. To avoid it, a small internal clutch, controlled by a solenoid, locks the converter and makes the link direct. The ECU checks that, with the clutch locked, engine and gearbox turn at the same speed. If it sees a difference, it stores P0741.

Symptoms

  • On the motorway the revs hunt, or sit higher than usual at a steady speed.
  • Higher fuel consumption.
  • A light shudder, like driving over a rippled surface, at around 40 to 55 mph.
  • Sometimes no symptoms, just the light.

Most likely causes, in order

  • Old or low transmission fluid: the number one cause, because the clutch runs in fluid and is operated by it.
  • The solenoid that controls the converter clutch, or its wiring.
  • A worn converter clutch.
  • Low fluid pressure in the gearbox, from a clogged filter or other causes.

What to check before the garage

  • Ask or find out when the transmission fluid was last changed. On many automatics the handbook calls it lifetime fluid, but it isn't.
  • Look for fluid stains under the car near the gearbox.
  • On the motorway at a steady speed, watch the rev counter: if it rises and falls on its own without you touching the throttle, note it.

At the garage: what to ask for

A check of fluid level and condition, then a fluid and filter change if it's old. If the code returns, a test of the converter clutch solenoid and a reading of the speed difference between engine and gearbox. A garage that works on automatic gearboxes is the better choice.

What DrivePulse shows

When the code reaches the OBD port, DrivePulse reads P0741 and opens its card, with the typical symptom of hunting revs on the motorway and the question about the last fluid change.

The live Dashboard shows revs and speed. At a steady speed, revs that rise and fall for no reason are the clue the garage wants to hear about. In your trips, average consumption creeping up with no other explanation points the same way. While driving, the passenger watches the screen, not the driver.

Frequently asked questions

Can a fluid change fix P0741?

Often yes, if the fluid was old and the clutch isn't worn yet. That's why it's worth doing soon.

Can I drive with P0741?

Yes, but it gets worse over time: the fluid overheats and degrades. Better not to put it off for months.

Does it apply to dual-clutch gearboxes?

No. P0741 concerns the torque converter, found in conventional automatics. Dual-clutch and automated manuals have different codes.

Related codes

Related guides

What you need to read it

All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.

DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.

← All codes