EN ▾
EnglishItalianoDeutschFrançaisEspañolPortuguêsČeštinaPolskiMagyarRomână
Download
  1. DrivePulse
  2. Fault codes
  3. Automatic transmission
  4. P0711

P0711: transmission fluid temperature sensor range/performance

An automatic gearbox adjusts its shifts to the temperature of its fluid. With P0711 the sensor reading doesn't add up: it doesn't rise as it should, it jumps, or it doesn't fit with the rest of the car.

Get DrivePulse

What to look at in live data

With P0711 the transmission fluid temperature sensor gives believable values that don't fit the running time: the temperature doesn't rise as it should, rises too fast or stays still. If the car reports transmission fluid temperature, follow it from a cold start together with engine coolant temperature: within 15 to 20 minutes of normal driving, with the phone in the hands of the person in the passenger seat, it should climb by quite a few degrees.

A temperature that stays still for the whole trip means a sensor stuck on one value; one that jumps in steps, a doubtful contact. A temperature that really climbs too high may be genuine, though: low fluid, old fluid or a clogged transmission cooler. Before replacing the sensor, check the level and colour of the transmission fluid, where it can be checked.

How serious is it, can you drive?

Severity is medium. You can usually drive gently, avoiding towing and heavy loads until it's checked. If shifts turn harsh or the gearbox stays in one gear, get to a garage soon: without a reliable temperature the gearbox can't protect its fluid properly.

Read P0711 on your car

With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.

Get DrivePulse

What it means

Inside the automatic gearbox a sensor measures the fluid temperature. The transmission control unit uses it to decide when to shift, with how much pressure and when to lock the torque converter: when cold it shifts later and more gently, when hot it protects the fluid.

With P0711 the electrical circuit works, but the value isn't believable. For example, after a good stretch of road the temperature stays where it was with a cold engine, or it jumps in ways real fluid can't, or it doesn't agree with the engine temperature.

Symptoms

  • Often just the engine light.
  • Harsher or later shifts than usual.
  • The torque converter locking up late, with a little higher fuel use.
  • Sometimes the gearbox goes into limp mode and stays in one gear.

Most likely causes, in order

  • The temperature sensor drifting with age.
  • The transmission fluid old and degraded, or at the wrong level.
  • The sensor wiring or connector, which work immersed in hot fluid.
  • The gearbox really running too hot, for example when towing, less often.

What to check before the garage

  • If the gearbox has a dipstick, the level and colour of the fluid, following the handbook: it is usually measured with the engine running and warm.
  • Oil stains under the gearbox.
  • When the transmission fluid was last changed, if ever: many gearboxes need it even if it's called "lifetime".
  • Note whether the code comes after a long trip, uphill or with a load, or already when cold.

At the garage: what to ask for

A live reading of the transmission fluid temperature, compared with the engine temperature, a check of the fluid level and condition, and a measurement of the sensor at its connector. On many gearboxes the sensor sits inside, on the internal harness or in the control unit, and replacing it means dropping the pan. A shop that works on automatic gearboxes is the better choice.

What DrivePulse shows

DrivePulse reads P0711 and its card advises changing the transmission fluid if it's old and seeing a transmission specialist if the code comes back; it also tells you whether the code is pending or confirmed.

If P0700 appears too, DrivePulse shows them together: P0700 only says the gearbox has a fault, P0711 says which one.

Frequently asked questions

Can I drive with P0711?

Usually yes, gently, avoiding towing and heavy loads. If shifts turn harsh or the gearbox goes into limp mode, get to a garage soon.

Is changing the transmission fluid enough?

Sometimes it helps, if the fluid is old. If the sensor has drifted, the code comes back and the sensor needs replacing.

What's the difference from P0712 and P0713?

P0712 and P0713 say the signal is too low or too high, an electrical problem. P0711 says there is a signal, but the value isn't believable.

Related codes

Related guides

What you need to read it

All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.

DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.

← All codes