EN ▾
EnglishItalianoDeutschFrançaisEspañolPortuguêsČeštinaPolskiMagyarRomână
Download
  1. DrivePulse
  2. Fault codes
  3. Electronics and communication
  4. U0426

U0426: invalid data received from immobilizer control module

The key has a chip that the electronic immobilizer reads before giving the engine ECU the go-ahead. With U0426 the engine ECU has received a message from the immobilizer that it didn't accept. Often the engine won't start, or starts and dies after a couple of seconds.

Get DrivePulse

What to look at in live data

At start-up the engine ECU has to receive the immobilizer's go-ahead, and with a weak battery that exchange can fail. Watch the voltage with the ignition on and as you turn the key: at rest around 12.4-12.7 V, and during cranking not much below 10 V. If it drops further, sort out the battery before suspecting the immobilizer.

If engine data reads normally but the car will not start, communication with the ECU is working and the problem is in the content of the immobilizer message: the key, the antenna or codes that a garage has to realign. If engine data cannot be read at all, the fault is further upstream, in the power supply or the network between control units.

How serious is it, can you drive?

Severity is medium, and it depends on what happens. If the engine starts and keeps running, you can drive: the code probably comes from a past event, but get it checked so you're not left stranded. If the engine won't start or dies straight away, the car stays put until the problem is fixed.

Read U0426 on your car

With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.

Get DrivePulse

What it means

When you turn the key or press the button, an antenna around the ignition reads the chip in the key. If the code is right, the immobilizer sends the engine ECU a go-ahead message over the control unit network.

With U0426 that message arrived, but with content the engine ECU doesn't recognise as valid. To be safe, the ECU blocks starting or cuts the engine after a moment.

Symptoms

  • The engine won't start, even though the starter turns.
  • The engine starts and dies after a couple of seconds.
  • The immobilizer light, a padlock or a car with a key, flashes quickly.
  • Sometimes no symptoms: the code stays stored from a difficult start that's already past.

Most likely causes, in order

  • The key, not programmed or with a damaged chip, for example after a drop or a badly made copy.
  • Other chipped keys on the same key ring, interfering with the reading.
  • The antenna around the ignition or its connector.
  • The car battery weak while cranking.
  • Rarely, the engine ECU and immobilizer no longer paired after one of them was replaced.

Tests to do right away

  • Try the spare key: if it starts, the problem is in the first key.
  • Take the other chipped keys off the key ring and try again.
  • Check the battery: if the starter turns slowly, the immobilizer may not read the key properly.
  • If the key has a remote, replace its battery: on some cars it's also used for recognition.

If the car won't start

Don't keep trying over and over: you'll drain the battery, and on some cars the immobilizer locks for a few minutes after too many failed attempts. Do the tests above calmly, then leave the key in for a few minutes and try again.

If no key works and the battery is charged, the car needs to go to a garage on a tow truck or be seen by a mobile mechanic: it takes a scan tool that can talk to the immobilizer.

At the garage: what to ask for

Reading the codes in the immobilizer and the engine ECU, a test of how the key is read and, if needed, reprogramming the keys. In order of cost: remote battery, reprogramming, new key, ignition antenna; re-pairing the engine ECU and immobilizer is the most expensive case.

What DrivePulse shows

DrivePulse shows U0426 when the control unit that stored it answers on the OBD port, and opens the immobilizer card with the causes and tests to do; it also says whether the code is pending or confirmed.

In Health the cranking test tells you how far the battery voltage drops while the starter turns: if it collapses, a weak battery is the first suspect, before the key and the antenna.

Frequently asked questions

Can I drive with U0426?

If the engine starts and keeps running, yes: it's probably a past event. If it won't start or dies straight away, the car stays put until it's repaired.

Do I need a new key?

Not right away. First try the spare key, take the other keys off the key ring and check the battery.

What's the difference from U0401?

U0401 says invalid data arrived from the engine ECU. U0426 says the invalid data is coming from the immobilizer.

Related codes

Related guides

What you need to read it

All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.

DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.

← All codes