What to look at in live data
After a cold start many cars deliberately retard ignition timing to heat the catalytic converter quickly, and P050B says this didn't happen as expected. In the standard data, watch timing advance and rpm in the first 20 to 30 seconds after starting from cold: timing should be low, often close to zero or even below, while rpm stays a bit higher than usual.
If timing stays high, the ECU can't retard it without rpm dropping too far: the most common cause is an idle that can't hold (dirty throttle body, air leak, idle valve), and then P0505 or P0507 may appear too. Check coolant and intake air temperature at start-up as well: after a night parked they should be close to each other; if coolant reads much higher, the sensor is wrong and the warm-up strategy starts badly.
How serious is it, can you drive?
Severity is low. The engine runs normally and you can drive gently. The consequence is that the catalyst warms up later, so emissions rise for the first few minutes; with the light on the inspection test is at risk.
Read P050B on your car
With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.
Get DrivePulseWhat it means
The catalyst only cleans the exhaust when it's hot. To warm it quickly, just after a cold start the ECU fires the mixture a little later than normal: the engine produces less power, but the exhaust heats up sooner.
To keep the idle stable with retarded ignition, the ECU balances air and spark precisely. With P050B the actual timing has drifted too far from the planned value: usually because something has changed the idle conditions, not because the ignition is faulty.
Symptoms
- Engine light on, often with no other symptoms.
- Slightly rough or high idle for the first minutes from cold.
- Rarely a less certain start in the cold.
- The code only appears after cold starts, never with a warm engine.
Most likely causes, in order
- The engine temperature sensor reading wrongly: the ECU thinks the engine is warmer or colder than it is.
- A dirty throttle body or an air leak, which change the idle air and force the ECU to correct with the ignition.
- A weak battery at start-up.
- Worn spark plugs or coils.
What to check before the garage
- With the engine cold after a whole night, look at the coolant temperature: it should be close to the outside air temperature. If it's very different, the sensor is suspect.
- The battery condition: resting voltage and how the starter turns over.
- If there are idle or lean mixture codes, start with those.
At the garage: what to ask for
A data reading with a cold engine: engine temperature, idle speed, actual and planned timing. Then a throttle body clean if needed and a search for air leaks. Ignition parts are only replaced if the tests point to them.
What DrivePulse shows
DrivePulse reads P050B and its card explains why the ECU retards the ignition when cold; it also tells you whether the code is pending or confirmed.
Live coolant temperature, read with a cold engine, is the first check on the sensor. In Health, the resting battery voltage and the cranking test rule out a weak battery.
Frequently asked questions
Can I drive with P050B?
Yes, gently: the engine runs normally. But cold emissions rise and the inspection test is at risk.
Is the ignition faulty?
Hardly ever. More often it's the temperature sensor, the throttle body or an air leak.
Why does it only appear from cold?
Because the ECU only runs this check in the first moments after a cold start, when it needs to heat the catalyst.
Related codes
Related guides
- Buying a used car? What to check: a code cleared just before the sale shows up in the distance driven since the last clear.
What you need to read it
All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.
DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.