EN ▾
EnglishItalianoDeutschFrançaisEspañolPortuguêsČeštinaPolskiMagyarRomână
Download
  1. DrivePulse
  2. Fault codes
  3. Ignition
  4. P0301

P0301: cylinder 1 misfire detected

In the on-board test results (mode 06), the cylinder 1 counter is high and the others near zero; after swapping coil or plug it tells you at once whether the fault moved. Fuel trims near zero point to the cylinder itself. With a steady light and a fairly smooth engine, gently to the garage; if it flashes, stop.

Get DrivePulse

What to look at in live data

Many cars count misfires cylinder by cylinder in the on-board test results (OBD2 mode 06). With P0301 the cylinder 1 counter is high and the others are close to zero; after swapping coil or plug, that counter tells you straight away whether the problem has moved, without waiting for the light to come back.

Look at the fuel trims with the engine warm too: if they are close to zero, the cause is almost always in the cylinder itself (ignition, injector, compression). If they are well positive, also look for air getting in near cylinder 1, for example at the intake manifold gasket.

How serious is it and can you drive?

Severity is high. With a steady light and the engine running fairly smoothly, drive gently to the garage. With a flashing light or heavy shaking, no: stop, the catalytic converter gets damaged quickly.

Read P0301 on your car

With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.

Get DrivePulse

What it means

The ECU measures crankshaft speed at every firing: when one is missed, the crankshaft slows for an instant. Knowing where in the revolution that happened, it can tell which cylinder skipped. With P0301 it says the misfires are in cylinder 1. In the same way P0302, P0303 and so on point to the other cylinders.

Only one cylinder involved nearly always means a part belonging to that cylinder: the plug, the coil, the injector. A problem common to the whole engine, such as fuel or an air leak, would more likely give P0300.

If the check engine light flashes

Fuel that doesn't burn reaches the catalytic converter very hot and can ruin it within a few miles. Ease off straight away and stop as soon as it's safe.

Symptoms

  • The engine shakes at idle, as if limping.
  • Jerks under acceleration, especially uphill.
  • Less power and higher fuel consumption.
  • On a car running on LPG or CNG, the fault is often worse on gas than on petrol.

Most likely causes, in order

  • The cylinder 1 spark plug, worn or fouled.
  • The cylinder 1 coil, or on older engines the plug lead.
  • The cylinder 1 injector, dirty or with a faulty circuit (see P0201).
  • An air leak near that cylinder, such as an intake manifold gasket.
  • In the worst case, low compression: a valve not sealing or a damaged piston ring.

How to find the culprit

The classic garage trick is the swap. With the engine off and cold, swap the cylinder 1 coil with another cylinder's, say number 2, and drive for a while. If the code becomes P0302, the problem followed the coil: it's the coil. If it stays P0301, do the same with the plug, then look at the injector.

If the problem stays on cylinder 1 after swapping coil and plug, it's time for a compression test.

What DrivePulse shows

DrivePulse reads P0301 and opens its card, with the flashing light warning and the swap trick. When the ECU exposes them, it shows misfires cylinder by cylinder: after swapping the coil you see straight away whether the problem has moved.

On many cars DrivePulse also tells you how far you have driven with the light on, and in Health the engine mixture helps rule out an air leak.

Frequently asked questions

Can I drive with P0301?

With a steady light and the engine running fairly smoothly, gently to the garage. With a flashing light, no: stop.

Should I change all the spark plugs?

Yes, if they're old: they're replaced together. Coils are only replaced if faulty, and the swap between cylinders tells you which.

What's the difference from P0300?

P0300 means misfires on several cylinders or not located. P0301 names the exact cylinder, which makes the search simpler.

Related codes

Related guides

What you need to read it

All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.

DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.

← All codes