What to look at in live data
The injector circuit has no value of its own in the standard data, but a cylinder that gets no fuel shows. In the on-board test results (mode 06), if the car reports them, check the misfire counters: with P0201 they gather on cylinder 1. At idle the engine shakes and the fuel trims rise, because the oxygen sensor sees the oxygen from the cylinder that isn't burning.
With the engine off, the check is electrical: an injector connector that is loose or corroded, a broken wire, an open injector winding (high impedance injectors usually measure between 11 and 18 ohms; low impedance and direct injection injectors much less). If the fault comes and goes, move the wiring with the engine running, keeping clear of belts and fan, and watch whether idle rpm jumps: where that happens is what needs fixing.
How serious is it and can you drive?
Severity is high. A cylinder without injection makes the engine run badly and, on petrol engines, unburnt air also upsets the catalytic converter. Drive as little as possible, only to the garage, without full throttle. If the check engine light flashes, stop.
Read P0201 on your car
With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.
Get DrivePulseWhat it means
Each cylinder has an injector that the ECU opens for a fraction of a second, every cycle, with an electrical pulse. The ECU also checks that each injector circuit responds: with P0201 it says the cylinder 1 circuit is open, shorted or out of range. The code is about the electrical side: connector, wiring or the coil inside the injector.
Codes from P0202 upwards cover the other cylinders. The cylinder number follows the order set by the manufacturer.
Symptoms
- The engine runs rough and limps, especially at idle.
- A clear loss of power.
- Misfires, often with P0301 or P0300.
- On some cars, limp mode.
Most likely causes, in order
- The injector connector unplugged, corroded or with a broken clip.
- The wiring damaged by heat or animals.
- The injector's internal coil open circuit.
- Less often, the drive circuit in the ECU.
What to check before the garage
- If the injector is accessible, check with the engine off that the connector is firmly clipped in.
- Look at the wiring to the injectors: chewed sheathing, bare wires, burn marks.
- If there's been recent work under the bonnet, tell the garage: a connector not refitted properly is the most common cause.
At the garage: what to ask for
A resistance check of the injector and of the wiring back to the ECU, and a test of the drive signal. If the injector is open circuit it gets replaced, and on diesels it usually has to be coded to the ECU.
What DrivePulse shows
DrivePulse reads P0201 and opens its card, with the advice to use the car as little as possible if the engine is limping. When the ECU exposes them, DrivePulse shows misfires cylinder by cylinder: if they cluster on cylinder 1, that confirms the picture.
In Health, the engine mixture helps you see how much the ECU is compensating for the missing cylinder.
Frequently asked questions
Can I drive with P0201?
Only to the garage, as little as possible. The engine is running on fewer cylinders and, if the light flashes, it should be stopped.
Does the injector need replacing?
Not always. It's often the connector or a wire. The injector is replaced if its coil turns out to be open circuit.
What's the difference from P0301?
P0301 says there are misfires in cylinder 1, for any reason. P0201 says the cylinder 1 injector circuit is faulty, which is one possible cause of P0301.
Why does a new diesel injector need coding?
Because every diesel injector has small flow differences, measured at the factory and printed as a code on its body. The ECU uses that code to correct injection: without it, the engine can run worse.
Related codes
Related guides
- Buying a used car? What to check: a code cleared just before the sale shows up in the distance driven since the last clear.
What you need to read it
All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.
DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.