What to look at in live data
The value to watch is the pressure that drives the injectors while cranking: on common rail engines it is fuel rail pressure, which many cars report in the standard data; on systems where the injectors run on high pressure engine oil it is visible only through the manufacturer's diagnostics. While the starter turns, it should rise past the starting threshold within a few seconds (around 200 bar on many common rail engines); with P2291 it stays below and the engine turns over without firing.
Watch cranking speed too: with a weak battery cranking rpm stays low (below about 150 to 200 rpm) and the pump can't build pressure. If cranking speed is good, pressure is missing because of air in the system after the tank ran dry, a clogged diesel filter, an in-tank lift pump (where fitted) that does not deliver enough, a leak to the return line (injectors or regulating valve) or, where the injectors run on oil, a low oil level or leaking seals.
How serious is it, can you drive?
Severity is medium, and it depends on how the engine behaves. If it starts and runs well, you can drive gently to the garage, but it may not restart: avoid stopping far from home. If it won't start, or you smell fuel, stop trying and have the car taken to a garage.
Read P2291 on your car
With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.
Get DrivePulseWhat it means
Injectors only open and spray if the pressure that operates them is high enough. Depending on the engine it's fuel pressure or, on some diesels, the pressure of the oil that drives them. During cranking the ECU checks that it builds up quickly before it fires the injectors.
With P2291 that pressure stays too low while the starter is turning. That's different from P0087, which is about low pressure with the engine running.
Symptoms
- The engine cranks for a long time before starting, or won't start.
- It starts and dies shortly after.
- It gets worse in the cold or after standing for a long time.
- Engine light on.
Most likely causes, in order
- Low fuel in the tank, or air in the system after running dry or after a filter change.
- A clogged fuel filter, or on diesels fuel that thickens in the cold.
- A weak battery: the starter turns slowly and the pump can't reach pressure.
- The low-pressure pump sending too little fuel, or a leak in the system.
- The pressure sensor or regulator, and only last the high-pressure pump.
What to check before the garage
- The fuel level: with the gauge near reserve, add some before looking further.
- The battery: if the starter turns slowly, charge it before trying again.
- Whether the fuel filter was changed recently or you ran dry: the air needs bleeding as the owner's manual says.
- A smell of fuel or stains under the car: in that case stop trying to start it.
- Don't keep the starter going for long: short attempts with a pause in between, so you don't flatten the battery.
At the garage: what to ask for
A live reading of requested and actual pressure while cranking, then the checks in order: filter, low-pressure pump, leaks, sensor and regulator. In order of cost the filter is cheap; the high-pressure pump and the injectors are the most expensive items, and should only be touched once everything else is ruled out.
What DrivePulse shows
DrivePulse reads P2291 and opens its card, with what to look at with the engine off and when not to use the car, for example if you smell fuel; it also tells you whether the code is pending or confirmed.
In Health you find the battery voltage, and the cranking test captures the lowest voltage while the starter turns: if the battery is weak, that's the first thing to fix.
Frequently asked questions
Can I drive with P2291?
If the engine starts and runs well, yes, gently as far as the garage, knowing it may not restart. If it won't start, don't keep trying.
What's the difference from P0087?
P0087 says the pressure is low with the engine running. P2291 says it doesn't rise far enough while the starter is turning.
Can a weak battery cause P2291?
Yes: if the starter turns slowly, the pump can't reach the pressure it needs. That's why the battery should be checked before replacing parts.
Related codes
Related guides
- Buying a used car? What to check: a code cleared just before the sale shows up in the distance driven since the last clear.
What you need to read it
All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.
DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.