What to look at in live data
The fuel volume regulator is the valve on the high pressure pump that decides how much diesel enters the pump, and so how much pressure reaches the rail. In the standard data, watch fuel rail pressure and, if the car reports it, the requested pressure: at idle a common rail diesel usually sits between 250 and 400 bar, and it climbs a lot when you accelerate. With P0004 the ECU sees the control signal too high, and actual pressure often no longer follows the request.
Since this is an electrical circuit fault, look first at the regulator connector and wires on the pump, often soaked in diesel or cooked by heat: a short to positive or a broken wire sets this code. If rail pressure drops and the engine stalls or goes into limp mode exactly when you move the wiring, you have found the spot. The valve is measured with the engine off: an open or shorted winding shows straight away in its resistance.
How serious is it, can you drive?
Severity is medium, but it depends on how the engine runs. Pressurised fuel is unforgiving: if the engine bucks, stalls or you smell fuel, don't drive and call a tow truck. If the engine runs well, drive very gently and only as far as the garage.
Read P0004 on your car
With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.
Get DrivePulseWhat it means
On direct-injection engines, above all common rail diesels, fuel pressure is set by metering how much fuel enters the high-pressure pump. An electric valve does this, the volume regulator, which the ECU opens and closes constantly.
With P0004 the ECU sees an electrical fault in the circuit that drives regulator A: the signal is higher than it should be, usually because of a broken wire, a short to positive or a failed coil. It's a circuit problem: P0087 and P0089 are about the resulting pressure instead.
Symptoms
- Hard starting, especially with a hot engine.
- The engine bucks, loses power or stalls.
- The ECU may put the engine into limp mode.
- Engine light on.
Most likely causes, in order
- The regulator connector corroded or loose.
- The regulator wiring damaged near the engine.
- A failed regulator coil.
- Missing power supply to the regulator.
- A dirty or sticking regulator from poor fuel, which makes the coil work badly.
What to check before the garage
- If you smell fuel in the engine bay or under the car, don't use the car.
- Don't touch fuel pipes, unions or components: the pressure can be extremely high.
- When the fuel filter was last changed: an old one puts strain on the regulator too.
- Whether the problem started after filling up: poor fuel can make the regulator stick.
At the garage: what to ask for
A live reading of requested and measured pressure, commanding the regulator with the diagnostic tool, measuring the coil and checking the connector and wiring. Connector and wiring cost little; the regulator costs more and on some pumps can only be replaced together with the pump, which is the most expensive item.
What DrivePulse shows
DrivePulse reads P0004 and opens its card, with the warning not to use the car if you smell fuel and not to touch the pressurised pipes; it also tells you whether the code is pending or confirmed.
If P0087 or P0089 show up too, DrivePulse lists them together: the control fault and the wrong pressure that follows should be read as one problem.
Frequently asked questions
Can I drive with P0004?
Only if the engine runs well, very gently as far as the garage. If it bucks, stalls or you smell fuel, no: call a tow truck.
What's the difference from P0087 and P0089?
P0004 is an electrical fault in the regulator's control circuit. P0087 and P0089 say the fuel pressure is too low or isn't following the requested value.
Do I need a new pump?
Not straight away. First the connector, wiring and regulator coil are checked; the pump only comes into it if the regulator can't be replaced on its own.
Related codes
Related guides
- Buying a used car? What to check: a code cleared just before the sale shows up in the distance driven since the last clear.
What you need to read it
All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.
DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.