What to look at in live data
P0093 is set when the ECU sees fuel rail pressure much lower than it should get for the flow it is asking of the pump. In the standard data, watch rail pressure and, if the car reports it, requested pressure: if the actual value collapses under acceleration (read by the person in the passenger seat while driving) or stays well below the request even at idle, the fuel is going somewhere.
First of all, look and smell for an external leak: a cracked high pressure pipe or a fitting seeping diesel onto a hot engine is a fire risk, and the car must not be used until it is fixed. If everything outside is dry, check the low pressure side first, since it costs less to check: a clogged diesel filter or an in-tank lift pump (where fitted) that does not deliver enough leaves the high pressure pump short of fuel, the pressure cannot hold and the ECU reads it as a leak. If that side is fine, the leak is internal: injectors returning too much to the return line, the pressure limiting valve on the rail not closing, or the regulator on the pump. At the garage the return flow of each injector is measured to find the one that leaks.
How serious is it and can you drive?
Severity is high, and the answer depends on what you smell and see. If there is a smell of fuel or a visible leak, stop somewhere safe, switch the engine off and don't drive on: there is a risk of fire, call a tow truck. If there is no smell and no leak and the engine runs well, drive very gently and only to the garage.
Read P0093 on your car
With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.
Get DrivePulseWhat it means
In common rail diesels and direct injection petrol engines a pump raises the fuel to a very high pressure, and a sensor on the rail measures it all the time. The control unit compares that pressure with the fuel it has just injected: if the pressure falls more than expected, or the pump has to work much harder than usual to hold it, it concludes there is a leak.
Large means the drop is big; the twin code P0094 means a small leak. The code doesn't say where the leak is: it can be on the high pressure side, between pump and injectors, or on the low pressure side, between tank and pump.
Symptoms
- A smell of diesel or petrol, inside the cabin or around the car.
- Fuel stains or drips under the engine, sometimes a shiny film on the pipes.
- Long cranking, the engine misfiring or stalling, little power.
- Check engine light on, often with reduced power; fuel consumption can rise for no reason.
Most likely causes, in order
- A fuel pipe or fitting cracked, loose or worn, on the high or the low pressure side.
- A leaking injector, or a damaged injector seal; on diesels also a broken or detached injector return line.
- The high pressure pump or the regulator leaking from their seals.
- The rail pressure sensor reading wrong: it happens, but less often, and you only find out after ruling out a real leak.
What to check before the garage
- If you smell fuel, switch the engine off and keep flames and cigarettes away before you look at anything.
- With the engine off, look under the car and along the pipes in the engine bay without touching anything: the system is under pressure.
- Don't tighten fittings yourself and don't start the engine to see where it comes out: a jet of fuel under pressure can injure you and catch fire.
- Think back to recent work on the injectors, the fuel filter or the pump: a fitting put back badly is a common cause.
Large or small leak: P0093 and P0094
Both codes come from the same check and differ only in how far the pressure drops. P0094 means the drop is small: often a fitting that seeps or an injector return that leaks a little. P0093 means the drop is big, and a visible leak is more likely.
In both cases the garage looks for the leak the same way. The difference matters to you: with P0093 there is more chance of fuel on a hot engine, and the first check is your nose.
At the garage: what to ask
A search for the leak on pipes, fittings, injectors and pump, a pressure test of the system and, on diesels, an injector return test. Only then a check of the pressure sensor. In order of cost: fitting or pipe, injector seals or return line, injector, high pressure pump.
What DrivePulse shows
DrivePulse reads P0093 and opens the fuel leak card, with advice in two parts: if you smell fuel or see a leak, stop, switch off and don't drive on; if there is neither, drive very gently to the garage. The card also says not to tighten fittings yourself, and DrivePulse tells you whether the code is pending or confirmed.
If P0087 or P0089 show up too, you see them in the same list. In live data, on cars that report it, you find the fuel rail pressure: look at it with the engine running and the car standing still, and if it stays low or drops even at idle, that is one more clue to take to the garage.
Frequently asked questions
Can I drive with P0093?
It depends. With a smell of fuel or a visible leak, no: stop, switch off and call a tow truck. With no smell, no leak and the engine running well, only very gently to the garage.
What's the difference from P0094?
It's the same check with a different threshold: P0094 is a small leak, P0093 a large one. With P0093 you are more likely to find visible fuel on the engine.
Can it be just the sensor?
Yes, sometimes the pressure sensor reads wrong. But you only find that out after looking for the leak: until it is ruled out, treat it as fuel getting out.
Related codes
Related guides
- Buying a used car? What to check: a code cleared just before the sale shows up in the distance driven since the last clear.
What you need to read it
All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.
DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.