What to look at in live data
Compare the fuel rail pressure the ECU asks for with the actual one, if the car reports the fuel pressure control data. At idle they should be close; the most telling moment is firm acceleration, when the request jumps, where it is safe, with the phone in the hands of the person in the passenger seat.
If actual pressure falls behind only under load, suspect the low pressure supply: a clogged fuel filter, the pump in the tank, air in the lines. If it is low at idle too, look at the high pressure pump and the regulator. A faulty sensor gives readings that jump for no reason.
How serious is it and can you drive?
Severity is high. The engine can stall while you drive, which is dangerous when overtaking or on a motorway. Only drive as far as you need to reach a garage, without full throttle. A high-pressure pump that is wearing out can send metal debris through the system: that's why it's not worth carrying on for weeks.
Read P0087 on your car
With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.
Get DrivePulseWhat it means
On common-rail diesels and direct-injection petrol engines, fuel reaches the injectors from a shared pipe, the rail, at very high pressure. A sensor measures rail pressure and the ECU compares it with the pressure it asked for. If it stays too low for a while, it stores P0087.
Like every code of this kind, P0087 doesn't point to a part: it says the pressure is missing. It can be missing because too little fuel reaches the pump, because the pump can't cope, or because pressure is being lost somewhere.
Symptoms
- Loss of power, especially under load and uphill.
- Long cranking, sometimes the car won't start.
- Jerking or stalling while driving.
- Limp mode.
Most likely causes, in order
- A clogged fuel filter, especially if it hasn't been changed for many miles. On diesels it's the most common and cheapest culprit.
- Water or waxed diesel in the filter, in winter or after a bad fill-up.
- The low-pressure pump in the tank, sending too little fuel to the main pump.
- Often running the tank nearly empty, which lets the system suck in air.
- A worn high-pressure pump or its control valve.
- Injectors leaking too much back to the return line, on diesels.
- The pressure sensor reading wrong.
What to check before the garage
- When was the fuel filter last changed? If it was many miles ago, it's the first suspect.
- If the tank was nearly empty, fill it up and see whether the code returns.
- In winter, if the car stood in the cold, remember that diesel can thicken: then the problem shows when cold and fades as it warms up.
- Don't open or loosen the high-pressure pipes: the system can stay pressurised even with the engine off, and the spray is dangerous.
At the garage: what to ask for
A measurement of the supply pressure before the main pump, then a comparison of requested and actual rail pressure. On diesels, an injector back-leak test. The filter comes first: it's cheap and often solves it.
What DrivePulse shows
DrivePulse reads P0087 and opens its card, with the warning not to work on the pressurised system yourself. In the live data, on cars that report it, you find fuel rail pressure: if it drops when you accelerate or stays low when warm, the problem is confirmed. While driving, the passenger watches the screen, not the driver.
DrivePulse also tells you whether the code is pending or confirmed and, on many cars, how far you have driven with the light on.
Frequently asked questions
Can I drive with P0087?
Only to the garage, gently. The risk is that the engine stalls while you drive, and a struggling pump gets worse if you push it.
Can the fuel filter alone fix it?
Often yes. A clogged filter is the most common cause on diesels and the cheapest repair: always start there.
Why does it only happen in winter?
Cold diesel can thicken and struggle through the filter. If the code appears when cold and disappears as the engine warms up, that or water in the filter is nearly always the cause.
Related codes
Related guides
- Buying a used car? What to check: a code cleared just before the sale shows up in the distance driven since the last clear.
What you need to read it
All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.
DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.