What to look at in live data
The code means the boost pressure sensor signal is too high to be real. The simplest test is with the ignition on and the engine off: the sensor should read almost the same as barometric pressure, around 1000 hPa (100 kPa) at sea level.
If it reads much more, or its maximum value, the problem is almost always electrical: the sensor, its connector or a wire shorted to supply voltage. If it reads right with the engine off but under acceleration climbs well above the requested pressure, the turbo really is overboosting and the actuator needs checking. Do the acceleration test where it is safe, with the phone in the hands of the person in the passenger seat.
How serious is it, can you drive?
Severity is medium. With the wrong signal the ECU limits the turbo, so power drops but the engine is protected. Drive gently to the garage, without heavy loads. If instead the car surges oddly or the turbo makes noises, use it as little as possible and have it seen straight away.
Read P0238 on your car
With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.
Get DrivePulseWhat it means
In the air pipe after the intercooler, or on the intake manifold, there's a sensor that measures the pressure of the air pushed by the turbo. The ECU uses it to control the turbo and the fuel.
The sensor sends a voltage that rises with pressure. P0238 means that voltage has hit the top of the scale: it's almost always an electrical problem, such as a wire shorted or a missing ground, and only rarely a genuinely excessive pressure.
Symptoms
- Engine light on and limp mode, with little power.
- The turbo seems to have stopped working.
- Sometimes no symptoms besides the light, if the fault is intermittent.
- It may appear with other pressure codes, such as P0299 or P0234.
Most likely causes, in order
- The sensor connector, oxidised or with loose contacts.
- The signal wire shorted to positive, or the sensor ground broken: either way the ECU reads the maximum value.
- The sensor fouled with oil and soot, or failed. On diesels the oil vapour that passes through the intake ends up there too.
- A real overboost, less often, for example with a stuck turbo actuator.
What to check before the garage
- With the engine off, find the sensor (on the air pipe after the intercooler or on the manifold), unplug and replug the connector and look for green or oily contacts.
- Check that the sensor wiring isn't crushed or chafed near brackets and hot parts.
- If the sensor is very oily, mention it at the garage: the crankcase ventilation and the turbo are worth a look too.
At the garage: what to ask for
A sensor reading with the engine off: it should show atmospheric pressure, the same as the barometric sensor if the car has one. Then supply, ground and signal measured at the connector. The sensor is cheap, but if the fault is in the wiring, replacing it won't help.
What DrivePulse shows
DrivePulse reads P0238 and opens its card: causes in order, whether you can drive and what to check, and tells you whether the code is pending or confirmed.
On cars that report it, live boost pressure shows straight away whether the reading makes sense: with the engine off it should be close to air pressure, not at the top of the scale.
Frequently asked questions
Can I drive with P0238?
Yes, gently: the car usually goes into limp mode and there's little power. Avoid heavy loads and have it checked soon.
Does the sensor need replacing?
Not first. Very often the problem is the connector or wiring; the sensor is replaced after those have been checked.
What's the difference from P0234?
P0234 says the boost pressure really is too high. P0238 says the sensor signal is too high, almost always because of an electrical fault.
Related codes
Related guides
- Buying a used car? What to check: a code cleared just before the sale shows up in the distance driven since the last clear.
What you need to read it
All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.
DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.