EN ▾
EnglishItalianoDeutschFrançaisEspañolPortuguêsČeštinaPolskiMagyarRomână
Download
  1. DrivePulse
  2. Fault codes
  3. Turbo
  4. P2566

P2566: turbocharger boost control position sensor A circuit intermittent

The position sensor tells the ECU where the actuator that controls the turbo is. With P2566 its signal drops out or jumps for brief moments and then comes back. It's almost always a contact problem, not the turbo: it has to be tracked down patiently, because with the car standing in the garage everything often looks fine.

Get DrivePulse

What to look at in live data

With P2566 the boost control position sensor signal comes and goes: the ECU loses it for brief moments. If the car reports the variable geometry control data, leave the engine idling and watch the measured position for a few minutes: it should stay steady, without jumps toward zero or the maximum. Gently move the actuator connector and the wiring near the turbo, watching whether the value jumps.

If the fault shows only on the move or with the engine hot, watch requested and actual boost during normal driving, with the phone in the hands of the person in the passenger seat: sudden drops in pressure that coincide with a jerk and a warning light confirm the intermittent signal. Heat near the turbo cooks connectors and sleeves: often repairing the wiring is enough, without replacing the actuator.

How serious is it, can you drive?

Severity is medium. You can drive gently: when the signal drops out the car loses power, so avoid long overtakes and fast merges until it's fixed. If you feel sudden surges or a loud new whistle, slow down and have it checked straight away.

Read P2566 on your car

With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.

Get DrivePulse

What it means

The ECU constantly reads the position of the turbo's vanes or valve to meter the boost. If the signal makes an impossible jump, or drops to zero for a moment and then recovers, it can't trust that reading.

P2566 is the code for brief dropouts: the circuit isn't open all the time, as with P2562, but loses contact now and then. To be safe the ECU limits boost until the signal is reliable again.

Symptoms

  • Check engine light on, sometimes only after driving for a while.
  • Sudden losses of power that then pass, often after a pothole or a rough stretch.
  • Limp mode on and off: switching the engine off and on brings the power back.
  • A code that stays pending for a long time without being confirmed.

Most likely causes, in order

  • The sensor connector, with a spread or corroded terminal that only touches now and then.
  • A wire hardened or chafed by heat near the turbo, making contact depending on vibration.
  • The connector seal baked by heat, letting moisture in.
  • The sensor with an internal fault that only shows when hot.
  • A supply problem shared with other sensors, if several codes appear together.

What to check before the garage

  • With the engine off and cold, follow the cable from the sensor: look for scorched or crushed sections, or places where it rubs on metal.
  • Unplug and reconnect the connector and check the terminals are straight and clean.
  • Note when the problem appears: when hot, after a pothole, in the rain. This information saves the garage hours.

Heat and vibration: why it comes and goes

The sensor and its cable sit near the turbo, which gets extremely hot and then cools down on every trip. These cycles harden the connector plastic and spread the terminals: when cold the contact holds, when hot or with vibration it opens for an instant.

That's why the code often appears after driving for a while, or on rough roads, and disappears when the car is standing.

How a contact that comes and goes is found

At the garage the sensor signal is read live while the cable and connector are moved by hand, section by section: when the value jumps, the spot is found. The test can be repeated with the engine hot.

Replacing the sensor without this test is a gamble: if the fault is in the cable, the code comes back with the new part.

At the garage: what to ask for

A test of the cable and connector with the signal read live, cold and hot, before replacing parts. In order of cost: cleaning and securing the connector, cable repair, new connector, sensor, complete actuator if the sensor is built in.

What DrivePulse shows

DrivePulse reads P2566 and opens the turbo actuator card, with the checks to do on a cold engine; it also tells you whether the code is pending or confirmed. A code that stays pending for days is typical of contacts that come and go.

On the live Dashboard, on cars that report it, the boost pressure shows the sudden drops: have a passenger watch it, not you while driving.

Frequently asked questions

Can I drive with P2566?

Yes, gently: when the signal drops out the car loses power. Avoid long overtakes until it's fixed.

What's the difference from P2562?

P2562 points to a sensor circuit that is faulty all the time; P2566 to a signal that comes and goes, almost always from a poor contact.

The garage can't find anything: what now?

Bring your notes on when it happens and ask for the cable test with the signal read live, with the engine hot too. Standing still and cold, the fault often doesn't show.

Related codes

Related guides

What you need to read it

All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.

DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.

← All codes