EN ▾
EnglishItalianoDeutschFrançaisEspañolPortuguêsČeštinaPolskiMagyarRomână
Download
  1. DrivePulse
  2. Fault codes
  3. Turbo
  4. P2562

P2562: turbocharger boost control position sensor A circuit

With P2562 the ECU isn't getting a valid signal from the sensor that measures the turbo actuator position. It's an electrical fault: start with the connector and wiring.

Get DrivePulse

What to look at in live data

The boost control position sensor tells the ECU where the variable geometry vanes (or the electronic wastegate) are. If the car reports the variable geometry control data, look at the measured position with the ignition on and the engine off: it should be steady and plausible, neither at zero nor at the maximum. With the engine running, at idle and with a few throttle blips while parked, it should move smoothly following the command.

P2562 is a circuit fault: a value that jumps from one end to the other, or stays put while the command changes, points to the connector, the wiring or the sensor, which is often built into the actuator and replaced with it. Check requested and actual boost under acceleration too, with the phone in the hands of the person in the passenger seat: when the sensor is wrong the ECU may limit boost to be safe, and actual pressure stays well below.

How serious is it, can you drive?

Severity is medium. The engine is usually not harmed, because the ECU limits the turbo as a precaution. You can drive gently, knowing there is little power: no demanding overtakes and no heavy loads until it is fixed.

Read P2562 on your car

With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.

Get DrivePulse

What it means

On variable-geometry turbos the ECU needs to know at every moment where the vanes are, to control the boost. It reads that from a position sensor, almost always mounted on or inside the actuator.

P2562 concerns that sensor's circuit: the signal is missing, outside its electrical limits or interrupted. Without it the ECU won't trust itself to control the turbo and usually leaves it doing very little, in limp mode.

Symptoms

  • Engine light on.
  • Reduced power, sometimes right from start-up.
  • The turbo never seems to kick in, or comes and goes.
  • The problem may come and go with heat or vibration.

Most likely causes, in order

  • The actuator connector, oxidised or loose: it sits in a hot, dirty spot and is the most frequent cause.
  • The wiring near the turbo, hardened or baked by exhaust heat.
  • The position sensor has failed. It is often inside the actuator, and the whole actuator is replaced.
  • The engine ECU, much more rarely.

What to check before the garage

  • With the engine off and cold, unplug and replug the connector on the turbo actuator: look for green, wet or blackened contacts.
  • Follow the wiring as far as you can see it: look for baked sleeves, broken ties, wires touching the exhaust.
  • If the code only appears with a hot engine, tell the garage: it points to a wire or connector that opens up with heat.

At the garage: what to ask for

Measurements of the sensor's supply, ground and signal right at the connector, before any parts are changed. If the wiring is fine and the sensor gives no correct signal, the actuator or sensor is replaced, depending on how the turbo is built.

What DrivePulse shows

DrivePulse reads P2562 and its card tells you where to start, with the engine off and cold: the connector on the turbo actuator and the wires near the exhaust; it also tells you whether the code is pending or confirmed. A code that stays pending and never confirms suggests a contact that comes and goes.

On cars that report it, live boost pressure shows whether the boost is back to normal after the connector check.

Frequently asked questions

Can I drive with P2562?

Yes, gently: the ECU limits the turbo, so there's little power. Avoid overtaking and heavy loads.

Is the turbo broken?

Almost never. P2562 is an electrical fault in the sensor or its wiring; the turbo itself is usually fine.

Why does the code come and go?

Because it's often a contact that opens with heat or vibration. That's why the connector is the place to start.

Related codes

Related guides

What you need to read it

All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.

DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.

← All codes