EN ▾
EnglishItalianoDeutschFrançaisEspañolPortuguêsČeštinaPolskiMagyarRomână
Download
  1. DrivePulse
  2. Fault codes
  3. Turbo
  4. P2563

P2563: turbocharger boost control position sensor A range/performance

On diesels with a variable-geometry turbo, an actuator moves the turbine vanes and a sensor tells the ECU where they are. With P2563 the position it reads doesn't match the one it asked for.

Get DrivePulse

What to look at in live data

On many diesels with a variable geometry turbo, the ECU compares the vane position it commanded with the one the sensor on the actuator reads. If the car reports the variable geometry control data, watch the two positions together: they should move in step, at idle and under acceleration; on the move, the phone is held by the person in the passenger seat.

If the measured position stays still, jumps or lags behind, the problem is often the electronic actuator or its sensor. If it moves but boost pressure does not follow, the vanes may be held back by soot. Check requested and actual boost pressure too, as for P0299.

How serious is it, can you drive?

Severity is medium. The engine won't be damaged quickly, but in limp mode the car has little power just when you need it, when overtaking or joining a fast road. Drive gently to the garage, avoiding heavy loads and steep climbs with a full car.

Putting it off for long isn't wise: vanes that move with difficulty tend to get worse, and a seized turbo costs far more than a clean.

Read P2563 on your car

With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.

Get DrivePulse

What it means

A variable-geometry turbo has movable vanes around the turbine: closed at low revs to give boost straight away, open at high revs so the pressure doesn't overshoot. An actuator moves them, electric or vacuum-operated, and a position sensor tells the ECU where they really are.

With P2563 the ECU has compared the position it asked for with the one it reads, and they don't match: either the vanes aren't getting where they should, or the sensor is reading wrongly. The code doesn't say which, so you start with the simplest checks.

Symptoms

  • Engine light on and reduced power, often suddenly while accelerating.
  • The car goes into limp mode and comes back to normal after switching off and on again.
  • Boost arrives late or in surges.
  • Sometimes together with P0299 (boost too low) or P0234 (boost too high).

Most likely causes, in order

  • Vanes stuck with soot: the most common case on diesels that do a lot of town driving. The vanes move less and less and eventually stop.
  • The actuator or its position sensor has failed. On many turbos the sensor is inside the actuator and they are replaced together.
  • Vacuum hoses cracked or off, on cars where the actuator works by vacuum.
  • The actuator connector or wiring, baked by the heat because it sits close to the turbo and the exhaust.

What to check before the garage

  • With the engine off and cold, look at the actuator connector: it should be fully seated with no signs of burning.
  • On cars with a vacuum actuator, check that the rubber hoses aren't cracked or disconnected.
  • Note when the code appears: from cold, at full load, after a long run. It helps tell a mechanical problem from an electrical one.

At the garage: what to ask for

An actuator test with the diagnostic tool: the movement is commanded and the read position is checked against the requested one. If the vanes are stiff, cleaning the variable geometry is often enough. Replacing the turbo is the last step, only if the vanes are damaged.

What DrivePulse shows

DrivePulse reads P2563 and opens its card: what it means, whether you can drive, the causes in order and the checks to do. It also tells you whether the code is pending or confirmed.

On cars that report it, live boost pressure shows whether the boost arrives under acceleration or stays low: a useful comparison before and after the repair.

Frequently asked questions

Can I drive with P2563?

Yes, gently. If the car is in limp mode, avoid demanding overtakes and heavy loads, and have it checked soon.

Does the turbo need replacing?

Hardly ever as a first step. The connector, hoses and vane movement are checked first; cleaning the vanes is often enough.

What's the difference from P2562?

P2562 points to an electrical fault in the sensor circuit. P2563 says the signal is there, but the position doesn't match the requested one.

Related codes

Related guides

What you need to read it

All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.

DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.

← All codes