What to look at in live data
P0263 says cylinder 1 contributes less than the others to turning the engine: the ECU measures the small crankshaft acceleration at each firing and finds cylinder 1's weaker. At idle with the engine warm, watch rpm: with a weak cylinder idle has a regular beat and the engine shakes more than usual, especially when cold. In the on-board test results (mode 06), if the car reports them, the cylinder 1 misfire counter may rise too.
On diesels many ECUs balance each injector with a quantity correction, which only the manufacturer's diagnostics show: a cylinder 1 with a correction very different from the others points to a tired, dirty or leaking injector. If the values are all similar, check that cylinder's compression. On a petrol engine the same logic leads to the injector, plug, coil or valves of cylinder 1.
How serious is it and can you drive?
Severity is medium. If the engine runs reasonably well, drive gently to the garage. If the light flashes or the engine misfires badly, stop: unburnt fuel can ruin the catalytic converter.
Read P0263 on your car
With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.
Get DrivePulseWhat it means
At each firing the crankshaft speeds up a little. If all cylinders work equally, these pushes are even; if one pushes less, the ECU sees it and tries to correct that cylinder's fuel quantity.
When the correction reaches its limit, it stores P0263 for cylinder 1. It isn't yet a misfire like P0301: the cylinder works, but less than the others.
Symptoms
- Engine vibrating or running rough, especially at idle.
- Less power and higher fuel use.
- Check engine light on, flashing if misfires join in.
Most likely causes, in order
- Cylinder 1's injector dirty, worn or dripping: the most common cause, especially on diesels.
- The connector or wires of that cylinder's injector or coil, corroded or damaged.
- A worn spark plug or weak coil, on petrol engines.
- An air leak near cylinder 1, for example an intake manifold gasket.
- Low compression in cylinder 1: valves or piston rings.
What to check before the garage
- With the engine off, look at the coil and injector connectors: no loose wires or oil on the contacts.
- Note whether the engine vibrates more when cold or hot: the garage will want to know.
- Think about whether an injector was recently replaced without being coded.
The swap test
The simplest way to tell whether the part or the cylinder is to blame is to swap: the garage moves cylinder 1's injector or coil to another cylinder and checks whether the code moves with it.
If the code moves, the part is faulty. If it stays on cylinder 1, the search moves to the cylinder itself: an air leak or compression, which is measured with a dedicated test.
At the garage: what to ask
Reading each cylinder's corrections with the diagnostic tool, the swap test and, if needed, a compression test. In order of cost: connector or wires, spark plug or coil, cleaning or overhauling the injector, a new injector with coding, and only last any engine work.
What DrivePulse shows
DrivePulse reads P0263 and opens the cylinder card, with the swap trick and the warning about a flashing light; it also tells you whether the code is pending or confirmed.
In Health, when the ECU provides them, you'll find misfire counts for each cylinder: after the swap you can see whether the problem stayed on cylinder 1 or moved.
Frequently asked questions
Can I drive with P0263?
If the engine runs reasonably well, yes, gently to the garage. If the light flashes or the engine misfires badly, stop.
What's the difference from P0301?
P0301 says the mixture in cylinder 1 doesn't ignite. P0263 says cylinder 1 works, but less than the others: often it's the injector.
Does the injector need replacing?
Not straight away. First the swap test: if the code moves with the injector, that's it; if it stays on cylinder 1, the problem is elsewhere.
Related codes
Related guides
- Buying a used car? What to check: a code cleared just before the sale shows up in the distance driven since the last clear.
What you need to read it
All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.
DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.