What to look at in live data
On many direct injection engines, especially diesels, the ECU powers the injectors in groups with a dedicated supply voltage, and P2147 says the group A voltage is low: usually because of a short to ground in an injector or its wiring. In the standard data the effect shows at once: the engine runs badly or stalls, and in the on-board test results (mode 06), if the car reports them, the misfire counters rise on all the cylinders in the group, often two.
Check the control module voltage while cranking too: if the battery collapses, injector voltage can't rise and the code can appear without any injector fault. If the battery is good, the check is done with the engine off: unplug the injectors in the group one at a time and see whether the short disappears. An injector harness crushed under the engine cover or melted by heat is another frequent cause.
How serious is it and can you drive?
Severity is high. If the engine runs well you can drive gently to the garage. If it misfires, the light flashes or you smell fuel, stop: misfires overheat the catalytic converter and can ruin it.
Read P2147 on your car
With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.
Get DrivePulseWhat it means
The ECU controls each injector through its own wire, but the power often comes from a wire shared by several injectors: that's the group. Which cylinders belong to group A depends on the engine and is in the manufacturer's documentation.
With P2147 the voltage on this shared wire is too low. It means that somewhere the current goes to ground before it reaches the injectors, or that one injector draws much more than normal.
Symptoms
- Check engine light on, sometimes flashing if there are misfires.
- Engine running rough or misfiring, often on several cylinders at once.
- Less power, sometimes limp mode.
- In the worst cases the engine struggles to start or stalls.
Most likely causes, in order
- The injector wiring harness with worn insulation touching the engine: injectors sit in the heat, and the wires harden and crack.
- An injector connector corroded or oily, letting current through where it shouldn't.
- An injector with a shorted internal coil, pulling down the supply for the whole group.
- More rarely, the ECU, in the circuit that feeds the group.
What to check before the garage
- With the engine off and cold, look at the injector connectors without touching the fuel lines: loose wires, oil or dirt on the contacts.
- Follow the injector harness with your eyes: no squashed, burnt or bare sections.
- Think about whether any recent work was done on the engine, such as spark plugs or the cylinder head: a moved or pinched wire is a clue worth telling the garage.
- If you smell fuel in the engine bay, don't use the car.
Why several cylinders at once
A fault in a single injector usually sets a code naming that cylinder, such as P0201 for cylinder 1. P2147 is about the shared wire instead: that's why the trouble can affect every cylinder in the group at the same moment.
If one injector in the group is shorted, it alone can drag the voltage down for all the others. Unplugging it brings the supply back to normal: that's the test garages use to find it.
At the garage: what to ask
Measuring the voltage on the group's supply wire, then unplugging the injectors one at a time until the voltage returns to normal, and checking each coil's resistance. In order of cost: cleaning or replacing a connector, repairing the harness, a new injector with its coding, and only last the ECU.
What DrivePulse shows
DrivePulse reads P2147 and opens the injector card, with the advice to stop if the engine misfires or you smell fuel; it also tells you whether the code is pending or confirmed. When the ECU provides them, it shows misfires cylinder by cylinder: if they hit several cylinders at once, that fits a shared supply.
In Health you'll find the battery voltage at rest and while driving: it helps rule out a weak electrical system before hunting for the short in the wiring.
Frequently asked questions
Can I drive with P2147?
Only gently to the garage, and only if the engine runs well. If it misfires, the light flashes or there's a fuel smell, it's better to stop.
What's the difference from P0201?
P0201 is about the injector circuit of a single cylinder. P2147 is about the wire that feeds a group of injectors, so it can affect more than one.
Do all the injectors need replacing?
Almost never. Usually the fault is in the wiring or in one shorted injector, which the garage finds by unplugging them one at a time.
Related codes
Related guides
- Buying a used car? What to check: a code cleared just before the sale shows up in the distance driven since the last clear.
What you need to read it
All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.
DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.