What to look at in live data
If the car counts misfires per cylinder (OBD2 mode 06), see under which conditions the cylinder 2 counter grows: at idle, under load or only when cold. At idle and when cold, the injector and air getting in are frequent causes; under load, while someone else drives and the phone is held by the person in the passenger seat, the coil and plug are, as they give out when more voltage is needed.
Look at coolant temperature too when the misfires appear: if it happens mostly right after starting and then goes away, and there is white smoke with a sweet smell from the exhaust, ask the garage for a cylinder leak-down test before replacing parts.
How serious is it, can you drive?
Severity is high. With a steady light and the engine pulling fairly smoothly, drive gently to the garage without hard acceleration. With a flashing light, heavy shaking or coolant going down, stop.
Read P0302 on your car
With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.
Get DrivePulseWhat it means
Every combustion gives the crankshaft a push; when a cylinder skips a beat, it slows for an instant. The ECU measures these slowdowns and knows which cylinder they belong to: with P0302 it points to number 2.
Which one is cylinder 2 is in the handbook or the garage will tell you: on many inline engines you count from the timing belt or chain side. If the ECU finds it on its own, the cause is nearly always a part of that cylinder, not something common to the whole engine.
If the light flashes
A flashing light means heavy misfiring: fuel that doesn't burn reaches the catalytic converter red-hot and damages it within a few miles. Lift off the accelerator and stop as soon as you can do so safely.
Symptoms
- The engine shakes, especially at idle and at traffic lights.
- Hesitation when accelerating, more noticeable uphill or with a loaded car.
- Rising fuel consumption.
- A smell of unburnt petrol from the exhaust.
Most likely causes, in order
- The cylinder 2 spark plug, worn or fouled.
- The cylinder 2 coil, or the plug lead on older engines.
- The cylinder 2 injector, dirty or not opening properly.
- An air leak near that cylinder.
- In the worst case, low compression in cylinder 2.
If P0303 shows up too
Two neighbouring cylinders misfiring together deserve attention. On some four-cylinder engines, 2 and 3 share a double coil, and then that's the part to look at. If instead coolant is going down or white smoke comes from the exhaust, it may be the head gasket between the two cylinders: in that case don't drive, and have the car towed to the garage.
At the garage: what to ask for
Swapping the cylinder 2 coil with another cylinder's to see if the fault moves, then the same with the plug, an injector test and, if the problem stays on cylinder 2, a compression test. In order of cost: plug, coil, injector, engine repair.
What DrivePulse shows
DrivePulse reads P0302 and opens its card, with the flashing light warning; it also tells you whether the code is pending or confirmed. When the ECU exposes them, it shows misfires cylinder by cylinder: after swapping the coil you see straight away whether the problem has moved to another cylinder.
In Health, the engine mixture helps rule out an air leak; live coolant temperature helps you spot a cooling problem early if P0303 shows up too.
Frequently asked questions
Can I drive with P0302?
With a steady light and the engine fairly smooth, gently as far as the garage. With a flashing light or heavy shaking, stop.
What does it mean if P0303 is there too?
Two neighbouring cylinders are misfiring: it can be a shared double coil or, if coolant is going down, the head gasket.
What's the difference from P0301?
The check is the same, only the cylinder changes: P0301 points to cylinder 1, P0302 to cylinder 2.
Related codes
Related guides
- Buying a used car? What to check: a code cleared just before the sale shows up in the distance driven since the last clear.
What you need to read it
All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.
DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.