EN ▾
EnglishItalianoDeutschFrançaisEspañolPortuguêsČeštinaPolskiMagyarRomână
Download
  1. DrivePulse
  2. Fault codes
  3. Ignition
  4. P0303

P0303: cylinder 3 misfire detected

The ECU has counted too many misfires in cylinder 3: the mixture there isn't burning every time it should. First it helps to know which cylinder is number 3 on your engine, then you start with the spark plug and the coil.

Get DrivePulse

What to look at in live data

In the on-board test results (mode 06), if the car reports them, each cylinder has its own misfire counter: with P0303 cylinder 3 should show numbers well above the others. Look at them warm at idle and then over a stretch at steady load, with the phone in the hands of the person in the passenger seat: if misfires grow only under load, a worn plug or a coil leaking to ground are the first suspects.

If instead they climb mostly at idle and when cold, look at the fuel trims: a trim that is high only at idle points to an air leak near cylinder 3 or an injector delivering too little. After swapping the coil or plug with the next cylinder, the counters tell you straight away whether the problem has moved: if it stays on 3, the next step is a compression test.

How serious is it, can you drive?

Severity is high. If the light is steady and the engine runs fairly smoothly, drive gently without revving hard to the garage, as soon as you can. If the light flashes, slow down and stop as soon as you safely can: unburnt fuel reaches the catalytic converter and overheats it, and the converter is one of the most expensive repairs on a car.

Read P0303 on your car

With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.

Get DrivePulse

What it means

The ECU measures crankshaft speed tooth by tooth. When a cylinder doesn't fire, the crankshaft slows for an instant at that point in its turn, and from the position the ECU works out which cylinder missed.

P0303 appears when misfires in cylinder 3 pass a threshold: either enough to raise emissions, or so many that they could overheat the catalytic converter. In the second case the check engine light flashes.

Where cylinder 3 is

Cylinders are usually counted from the timing belt or chain side, but there are exceptions: the workshop manual or the diagram on the engine cover confirms it. On an inline four, number 3 is one of the two middle cylinders.

On three-cylinder engines, common in today's small petrol cars, cylinder 3 is the last in the row. A misfire there is easier to feel: with one cylinder in three working badly, the engine shakes noticeably even at idle.

Symptoms

  • Vibration at idle, felt through the steering wheel and seats.
  • Jerks or flat spots when you accelerate, worse uphill or in a high gear.
  • Uneven cold starts, with the engine running lumpy for the first few seconds.
  • A smell of unburnt fuel from the exhaust.
  • Check engine light on steadily, or flashing in severe cases.

Most likely causes, in order

  • The cylinder 3 spark plug, worn, fouled or with the wrong gap.
  • The cylinder 3 ignition coil, which suffers from heat and moisture.
  • The cylinder 3 injector, dirty, spraying too little or dripping.
  • An air leak near that cylinder's intake port, for example the intake manifold gasket.
  • Low compression in cylinder 3: a valve not sealing, worn rings or the head gasket.

If it comes back with a new plug and coil

When the plug and coil are new and the code returns, suspicion moves to the injector. A garage can swap it with another cylinder's: if the fault moves, you've found the culprit.

If the injector is fine too, you need a compression or leak-down test. On high-mileage direct-injection engines, carbon on the intake valves can be enough to make a single cylinder misfire: a dedicated cleaning removes it.

What DrivePulse shows

DrivePulse reads P0303 and opens its card, with the advice to start from the plug and coil; it also says whether the code is pending or confirmed, meaning whether the ECU has seen it once or several times in a row.

In Health, when the ECU exposes them, you find misfire counts for each cylinder: after a repair you can see whether the cylinder 3 count has stopped or moved to another one. Once the repair is done, Before the inspection tells you when the ECU's self-tests are ready again.

Frequently asked questions

Can I drive with P0303?

With a steady light, only gently and to the garage. With a flashing light, slow down and stop as soon as you safely can.

Which one is cylinder 3?

Cylinders are usually counted from the timing side, but the manual confirms it. On a three-cylinder it's the last in the row, on a four-cylinder one of the two in the middle.

I replaced the plug and coil and the code came back: now what?

Next come the cylinder 3 injector and a compression test. On direct-injection engines, carbon on the intake valves also matters.

Related codes

Related guides

What you need to read it

All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.

DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.

← All codes