EN ▾
EnglishItalianoDeutschFrançaisEspañolPortuguêsČeštinaPolskiMagyarRomână
Download
  1. DrivePulse
  2. Fault codes
  3. Mixture and intake air
  4. P0101

P0101: mass air flow sensor range/performance

With the engine warm and the scan tool held by the passenger, the mass air flow reading should be steady at idle and rise at once under acceleration; compare it with the fuel trims: well above zero under load means it reads less air than there really is. Before replacing it, check the hoses and the air filter. You can drive gently.

Get DrivePulse

What to look at in live data

The mass air flow sensor tells the ECU how much air is coming in, in grams per second. With the engine warm and at idle the value should be steady; under acceleration it should rise at once and smoothly, without jumps or dips. On the move, the phone is held by the person in the passenger seat.

Compare it with the fuel trims: if under load the long term trim climbs well above zero, the sensor probably reads less air than there really is; if it drops well below, it reads more. Before replacing it, make sure no air gets in between the sensor and the engine (hoses, clamps) and that the air filter is not clogged or fitted crooked.

How serious is it and can you drive?

Severity is medium. You can drive gently: the ECU switches to backup values and the engine runs, perhaps worse. It's worth fixing soon, because a wrong mixture over time fouls the catalytic converter and, on diesels, loads the particulate filter faster.

Read P0101 on your car

With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.

Get DrivePulse

What it means

The mass air flow sensor sits between the air filter and the engine and measures how much air comes in. The ECU uses that figure to decide how much fuel to inject. P0101 doesn't say the sensor is disconnected: it says its reading doesn't match what the ECU expects from revs, throttle position and manifold pressure.

On diesels the MAF also works with the EGR valve, which sends part of the exhaust gas back into the engine. If the EGR stays open when it shouldn't, less fresh air comes in and the MAF reading can look wrong even though the sensor is fine.

Symptoms

  • Sluggish or jerky acceleration.
  • Rough idle, sometimes the car stalls when you lift off.
  • Higher fuel consumption.
  • On diesels, black smoke under acceleration and sometimes limp mode.

Most likely causes, in order

  • An air leak after the sensor: a cracked hose or loose clamp between MAF and engine. Air that gets in there isn't measured.
  • A dirty sensor, with dust, or oil if the air filter is a washable oiled type.
  • The air filter clogged or badly fitted.
  • On diesels, the EGR clogged or stuck.
  • The sensor connector or wiring corroded.
  • A failed sensor, once everything else checks out.

What to check before the garage

  • Look at the air filter and how it sits in its housing.
  • Check the hose between MAF and engine: flex it by hand with the engine off to spot cracks in the folds.
  • Clean the sensor with dedicated MAF cleaner spray: remove the sensor, spray from a distance and let it dry. Never touch the thin wires of the element and don't use compressed air or other sprays. It's the first attempt, and the cheapest.
  • Make sure the connector is fully seated and not corroded.

At the garage: what to ask for

A comparison of measured and expected air flow at different revs, an intake leak test and, on diesels, a check of the EGR valve. The sensor gets replaced afterwards, if the reading stays wrong with everything else in order.

What DrivePulse shows

DrivePulse reads P0101 and opens its card with causes, checks and advice on how to clean the sensor. In the live data, on cars that report them, you find MAF air flow, revs and throttle: at idle the flow should be low and steady, and rise smoothly with revs.

In Health, the engine mixture helps you tell whether there's an air leak as well as the MAF problem.

Frequently asked questions

Is cleaning the MAF enough?

Often yes, if dirt was the problem. Use the specific spray and don't touch the element. If the code returns after cleaning, look for air leaks, and only then replace the sensor.

Can I drive with P0101?

Yes, gently. The engine uses backup values and runs, but fuel economy and performance suffer.

How is it related to P0171?

A MAF that reads less air than is really coming in makes the ECU inject less fuel: the mixture turns lean and P0171 can appear too.

Related codes

Related guides

What you need to read it

All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.

DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.

← All codes