What to look at in live data
P0170 says the bank 1 mixture correction has gone out of limits, without saying which way: the live data tells you. Watch short and long term fuel trims with the engine warm: added together, well above zero means the ECU is adding fuel (lean mixture), well below zero means it is taking fuel away (rich mixture). Beyond 20 to 25% either way, depending on the car, the code appears.
Once you know the direction, the path is the one for P0171 or P0172. Compare idle with about 2,500 rpm in neutral: a high trim at idle that falls as revs rise points to an air leak; a trim that is the same at every speed suggests fuel pressure or the mass air flow sensor. Look at the oxygen sensor ahead of the converter too: if it isn't switching, the trim is based on a wrong reading.
How serious is it, can you drive?
Severity is medium. You can drive gently, but don't leave it for months: a mixture that stays wrong leads to higher consumption, misfires and catalytic converter damage. If the light flashes or the engine jerks, slow down and stop as soon as you can.
Read P0170 on your car
With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.
Get DrivePulseWhat it means
The oxygen sensor in the exhaust says whether combustion has too much air or too much fuel, and the ECU adjusts injection to match. That adjustment has two parts: a fast one that changes all the time, and a slow, long-term one that adapts to engine wear.
With P0170 the correction has gone past the limit the ECU allows itself on bank 1. Unlike P0171, which says lean, and P0172, which says rich, P0170 doesn't give the direction: you find it from the sign of the long-term correction.
Symptoms
- Engine light on, often with nothing else.
- A rough or hunting idle.
- Flat spots when accelerating or higher fuel consumption.
- Over time, misfires if the mixture stays badly off.
Most likely causes, in order
- An air leak after the MAF: a cracked duct, a loose clamp, a vacuum hose.
- A dirty MAF sensor measuring the air wrongly.
- Fuel pressure too low or too high.
- Dirty or dripping injectors.
- The air filter clogged or badly fitted.
What to check before the garage
- The sign of the long-term correction: positive means the ECU is adding fuel, so the engine is on the lean side; negative means it's taking fuel away, so it's on the rich side.
- If it's on the lean side, with the engine running listen for a hiss near the intake and look at ducts and clamps after the air filter.
- If it's on the rich side, look at the air filter and think about the injectors or fuel pressure.
- The MAF: clean it only with the dedicated spray, never compressed air.
At the garage: what to ask for
A live reading of the corrections at idle and at higher revs, a smoke test to find air leaks and, if there aren't any, a fuel pressure measurement and a MAF check. In order of cost: clamp or duct, MAF cleaning or replacement, injectors or pump.
What DrivePulse shows
DrivePulse reads P0170 and opens its card, with the same checks as P0171 and P0172 and the tip to look at the sign of the long-term correction; it also tells you whether the code is pending or confirmed.
In Health you find the engine mixture with the long-term fuel trim: its sign tells you straight away whether to look for an air leak or too much fuel. In the live data you can compare the corrections at idle and at higher revs.
Frequently asked questions
Can I drive with P0170?
Yes, gently, but don't leave it for months. If the light flashes or the engine jerks, stop as soon as you can.
What's the difference from P0171 and P0172?
P0171 says lean, P0172 says rich. P0170 only says the correction is out of limits, without the direction.
How do I tell whether it's lean or rich?
From the sign of the long-term correction: positive, the ECU is adding fuel and the engine is on the lean side; negative, it's taking fuel away and it's on the rich side.
Related codes
Related guides
- Buying a used car? What to check: a code cleared just before the sale shows up in the distance driven since the last clear.
What you need to read it
All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.
DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.