EN ▾
EnglishItalianoDeutschFrançaisEspañolPortuguêsČeštinaPolskiMagyarRomână
Download
  1. DrivePulse
  2. Fault codes
  3. Turbo
  4. P2263

P2263: turbo boost system performance

Boost pressure isn't following what the ECU asks for, too low or sometimes too high. It's a very common code on diesels that do a lot of town driving.

Get DrivePulse

What to look at in live data

P2263 means boost is not behaving as expected: usually too little, more rarely too much. Compare requested and actual pressure (the boost control data, or intake manifold pressure minus barometric pressure) during firm acceleration from about 1,500 rpm, where it is safe, with the phone in the hands of the person in the passenger seat.

If actual pressure stays below, look for air leaks and check the wastegate or vanes. If it overshoots, the turbo is not being held back and the actuator or its solenoid valve is the suspect. With the ignition on and the engine off, the pressure sensor should read almost the same as barometric pressure.

How serious is it and can you drive?

Severity is medium. You can drive gently to a garage. Limp mode limits power and protects the engine, but it makes overtaking and joining a motorway risky: keep that in mind. If blue smoke or oil leaks appear, stop.

Read P2263 on your car

With an OBD2 adapter, DrivePulse reads your car's fault codes and tells you what they mean, whether you can drive and what to check. It's read-only: it writes nothing to the ECU.

Get DrivePulse

What it means

The ECU asks the turbo for a pressure and checks, moment by moment, that the real pressure follows. P2263 means the two haven't matched for a certain time. Unlike P0299, which only says too little, P2263 is broader: boost isn't following the command, and the reason can also be a turbo that reacts too slowly.

On diesels with a variable-geometry turbo it's often linked to soot: the vanes that control the flow get coated and move badly.

Symptoms

  • Loss of power, sometimes sudden, with limp mode.
  • Switching the car off and on again brings it back to normal, until the next hard pull.
  • Black smoke under acceleration on some diesels.
  • Often together with codes on the particulate filter or the EGR.

Most likely causes, in order

  • Sooted-up variable geometry, typical of diesels that mostly do short trips.
  • Air leaks in the hoses or the intercooler, as with P0299: a frequent cause, and one of the cheapest to fix.
  • The turbo actuator: a vacuum one with a loose line or a faulty control valve, or an electric one that has failed.
  • An EGR valve stuck open, taking exhaust gas away from the turbo.
  • A restricted exhaust or intake: a heavily loaded particulate filter, a dirty air filter.
  • The pressure sensor reading wrong.

What to check before the garage

  • With the engine off and cold, check the hoses and clamps between turbo and engine, and the thin vacuum lines going to the turbo.
  • Look at the air filter.
  • Read all the codes: if there are particulate filter codes too, start there.
  • If the car does mostly town driving, half an hour at a steady speed can help. It isn't a repair: if the code comes back, it needs a garage.

At the garage: what to ask for

A comparison of requested and measured boost on a road test, a test of the actuator and the variable geometry, and a boost leak test. On many diesels sooted vanes can be cleaned without replacing the turbo.

What DrivePulse shows

DrivePulse reads P2263 and opens its card with the causes and checks. In the live data, on cars that report it, you see manifold pressure while you accelerate: if it rises late or in steps, the turbo control isn't smooth. While driving, the passenger watches the screen, not the driver.

On diesels, DPF status in Health tells you how loaded the filter is and how many regenerations were interrupted: a full filter is one of the causes of this code.

Frequently asked questions

Why does power come back after restarting?

Because the ECU starts again without the limit. The fault is still there, and limp mode will return at the next hard pull.

Does the turbo need replacing?

Often not. The most common causes are air leaks, vacuum lines and sooted vanes, which can be cleaned. The turbo gets replaced when it's really damaged.

What's the difference from P0299?

P0299 says boost is too low. P2263 says it isn't following the command: it can be low, high or late. The causes largely overlap.

Related codes

Related guides

What you need to read it

All you need is an ELM327 OBD2 adapter, plugged into the diagnostic port, usually under the steering wheel. On iPhone it has to be Bluetooth Low Energy (BLE) or Wi-Fi, like the Veepeak OBDCheck BLE or the Vgate iCar Pro 2S; on Android classic Bluetooth adapters work too, once paired in the phone's settings. Veepeak recommends DrivePulse to its customers, and the Vgate is the one the Italian site Macitynet tested together with the app. The full list is on Which adapters work.

DrivePulse is on iPhone and Android. It's read-only: it writes nothing to the ECU and doesn't clear codes. You try it for 7 days from the first connection or for 15 trips, whichever comes first, then unlock it with a single purchase, no subscription and no account.

← All codes